Jump to content
SAU Community

Recommended Posts

not white, they are silver. yeah they are made by BBS, a sort of mesh style. not sure if they are 17X8 or X9.

they are quite nice, but i wouldn't go out of my way to find a set.

hope this helps...

Grey one is the Vspec I

white is the Vspec II

slim jims right on the specs, but chances are they won't have the factory fitted rubber

i've got these info sheets for the nismo and n1 if anyone wants them.

post-27256-1150530405.jpg

post-27256-1150530733.jpg

post-27256-1150530826.jpg

post-27256-1150531042.jpg

Edited by Usual Suspect

Yeah 17x8+30 (close up pic attached). I gave up trying to find a spare set.

Mine even had orginal spec Potenza 245s on it when it arrived!

PM have a V-Spec II f/s at the moment, but a couple of things suggest it might not be a genuine example.

post-5400-1150861040.jpg

  • 3 years later...

I know this is an old thread, but I thought it would be appropriate to post my question here, are the r32 gtr v-spec rims the same as the Stagea Autech ones (e.g width)? Just with a different center cap? as I am currently looking at some with the Stagea center cap and if they were the same was just going to get the original center caps from Nissan. Thanks very much in advance.

hope this helps...

Grey one is the Vspec I

white is the Vspec II

slim jims right on the specs, but chances are they won't have the factory fitted rubber

i've got these info sheets for the nismo and n1 if anyone wants them.

can u post the Nismo Sheets up in here plz??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Before starting any work, we attempted to adjust the tune. However even after adjusting it to certain extremes like completely stopping fuel, it had no effect. What fixed it was removing the Nistune Board and installing the original EPROM instead. This immediately fixed the issue. Everything should have been fine with the Nistune Board installation, so I am unsure why it has caused a problem. The soldered connector is also properly soldered. This worked when I first got the 550cc injectors, before cleaning, but that may have been a coincidence.  We ended up not installing the fuel pump hanger (at least for now). So currently running stock injectors, stock fuel pump, stock fuel pump hanger – Well everything stock except the exhaust. Now I have around €1400 in Nistune, Injectors, and Hanger collecting dust for the time being, perhaps I'll install them in the future. For now I'll enjoy the car as is 😁 Thanks a lot for all your assistance, I really appreciate all the help you have given me.
    • The turbo can’t be the issue. They’re proven to make much much power than you’re making. There is something in the setup that isn’t correct. - has the exhaust got any silly step downs? - what exhaust manifold?
    • Ok, just the way you wrote it made it look like you had the stagger the wrong way around 
    • I was getting anxious with the DVLA not knowing if the paperwork is fine or not, so I rang them. No update had been given, but I  was reassured that providing the box was ticked on the V750 then the application will go through fine. I've been checking the DVLA website pretty much every day, in the hope that it would have been done. Fast forward to Monday 29th  and I was greeted with a new screen on the check, and it finally showed as Taxed and MOT'd, woohoo! The car was in desperate need of a clean, not knowing when this day was coming it was put off. As far as I was concerned I had another 3 weeks  I'm not normally one for using snow foam, but I wanted to give it another try It hasn't cleaned up too bad considering it's 21 years old and lived on a boat for a number of weeks. The personalised number plate is J2 XBK, an illegally spaced number plate would have it read J2X BK. BK could either represent  the colour black or Baker, which is my surname. I filmed the first drive, the Youtube link will be at the end. I used the same driving route I did with the 323F V6 when I had a new exhaust installed, heres a couple of photos A few more since then Youtube video can be viewed here: https://www.youtube.com/watch?v=TjkFHPzjGDw
×
×
  • Create New...