Jump to content
SAU Community

Recommended Posts

  On 28/04/2012 at 4:01 AM, dirtyRS4 said:

this takeros stag is hawt

Namnls2.png

well done sweden

my RS4S takeros stagea resides in victoria w00t w00t fresh from japan.

post-18938-0-67087400-1340722708_thumb.jpg

post-18938-0-44063900-1340722724_thumb.jpg

and its genuine, including the CF bonnet, could use some of those eyelids though.

Edited by OMY31T
  On 26/06/2012 at 3:00 PM, OMY31T said:

my RS4S takeros stagea resides in victoria w00t w00t fresh from japan.

and its genuine, including the CF bonnet, could use some of those eyelids though.

what size rims and what suspension setup?

Koya Endless 19x8.5 235/35 tyres +12 offset all round, you can have rims made to order from koya. suspension is HKS Performer all round - if you havent seen these before, they were made inbetween the hypermax I and hypermax II, i had never seen them until i got them with the stag from japan, and i will say, they are pefrect for the street, i have hks hypermx in my r33, and the hard rock solid, these are nice for the street and still handle really well, i think the wagon handles even better than my r33.

  • 2 weeks later...
  • 3 weeks later...

Yo!

Here's a few new pics now when the summer came to Sweden.

I also mapped the car with the new GT2530-turbos and the HKS 264/9.1 cams.

497whp at 1.4 bar, that's really impressing power at such a low pressure (still stock bottom).

Here's a movie, 50km/h to 220km/h: http://www.youtube.com/watch?v=OEAbxzyr8LQ

And here's a movie from the mapping (making ~400whp at 1.1 bar): http://www.youtube.com/watch?v=lVp8rNBlRgo

And here's the photos!

bild11.jpg

bild13.jpg

bild.jpg

IMG_1553.jpg

  On 30/07/2012 at 4:21 PM, TP_ said:

Yo!

Here's a few new pics now when the summer came to Sweden.

I also mapped the car with the new GT2530-turbos and the HKS 264/9.1 cams.

497whp at 1.4 bar, that's really impressing power at such a low pressure (still stock bottom).

Here's a movie, 50km/h to 220km/h:

http://www.youtube.com/watch?v=OEAbxzyr8LQ

And here's a movie from the mapping (making ~400whp at 1.1 bar):

http://www.youtube.com/watch?v=lVp8rNBlRgo

And here's the photos!

Wow that looks freaking sweet...

  On 05/08/2012 at 11:56 PM, bigkevracer said:

Eyelids would match the grill... is that Dolphin?

Good to see it back on the road!

Yeah its Dolphin...I need to check our their eyelids as the only ones I can find on YAJ looks a bit ghey.

Yeah need skirts and rear but fark its expensive getting it from RHDJ....I haven't seen nismo bodykits on YAJ for a while...

I think I got lucky when I scored this bar landed for $400...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
×
×
  • Create New...