Jump to content
SAU Community

Recommended Posts

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

you should leave the inlet manifold one hooked up. (pcv valve)

the turbo side should have the big one from the rocker cover going to it and thats it. simply block the suction pipe hole and leave the little filter on the can.

The T Piece runs to one of the inlets on the catch can. It used ot have two lines to it but then i couldn't have a breather (as the catch can didnt have one built in) so we used the 2nd inlet on the catch can and stuck a breather on that, but i am thinking that doesnt work... lol

Car only blows alot of smoke when you have put ur foot down into boost, on idle its very minimal

Some smoke comes out the rocker covers but when the catch can system is disconnected the car blows alot less smoke out of the exhaust system...

Im off to buy a decent catch can and see if that helps peeps!

Otherwise i think theres somethin else wrong aswell... maybe an oil drain/inlet problem?

I'd have to agree with the rest, That line off to the catch can is probably too restrictive and is causing the crank case to pressurise, when the crank case is pressurised the oil drain backs up and pushes oil out the turbo seals. happened to me when i had a retard attack and tried to use a hose and very restrictive brass air filter for my vent and had the same thing happen with my brand new garrett turbo. :(

Ive disconnected one of the lines that runs to the T piece and then to the catch can and the car seems to blow very little smoke now, still abit but about 90% less!

So obviously i need a better catch can set up and ill check the drain lines etc anyway on monday. I should be able to keep off a defect now tho :(

you basicly need to hook it up so ideally you would have large catch can with 3 fittings or 2 fittings and a vent.

two fittings for both rocker cover hoses.(the big ones)(plug the pcv valve)

and the thrid to atmosphere or back into the suction pipe :(

I will sent two hoses to the catch can and have the breather ontop of the catch can :(

Im still getting a tiny bit of smoke but im sure after the lines are looked at and the tuning plcae get it we can sort that out!

Thanks for the help so far peeps.

I don't understand how restrive lines or bad catch can - can cause that much white smoke -

I'm not saying this wasn't the case - just trying to understand the physics behind it - As I had a similar problem with my old car.

In my case the air intake route was blocked off, so all the bad oils etc have nowhere to go except to the catch can from the head. If the lines are too small or there is a problem with the breather then pressure can build up and force oil out in my case through the turbo's oil seal i believe?

The system needs to be able to expell the gas's and extra oils that build up in the combustion process basically...

In my case the air intake route was blocked off, so all the bad oils etc have nowhere to go except to the catch can from the head. If the lines are too small or there is a problem with the breather then pressure can build up and force oil out in my case through the turbo's oil seal i believe?

The system needs to be able to expell the gas's and extra oils that build up in the combustion process basically...

have you taken one of your intercooler pipes of to see if your intercooler is full of oil?

The intercooler had a slight build up of oil but nothing outta the ordinary. The wierd thing was oil got into the boost controllers actuator line! That messed with my controller but i let it out and pulled a line off the block and it runs fine now, i have to keep it like that until i get the new catch can next week because if i hook it back up it'll cause the oil problem again! As it is its not too bad at all.

Ok i replaced the catch can with a better set up, two lines running to it and it has a built in breather and i still get oil smoke....

Next up i will have the turbo oil line looked at to see if it has a restrictor on it otherwise check the line to the sump isnt blocked.

If its not that then i guess its the turbo oil seal??? :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...