Jump to content
SAU Community

Recommended Posts

Yeah as soon as it warms up a bit and UNI is over and done with ill be out and about for sure, cant wait!!

I'm like a hermit at the moment with all this UNI work, i only leave the house to go straight to school, work or the misseses place.

KNOW WHAT U MEAN!!! exactly the same! uni, work, gf. Can't wait till holidays. not long now!!!

newcastle rocks last time i was up there they finally started having some nice cars but 4 - 5 years ago it was funny as all hell seeing about 25 - 30 cars all of them riced up POS with massive chromies i am talking excels, lancers, corollas etc all from like late 80'/early 90's.

I was up there a year and half ago and started seeing alot more skylines, rexes etc more like canberra.

MAKE SURE YOU GO TO BLUE WATER PIZZA best pizza anywhere actually can you buy me some and bring it back :dry: oh how i miss that pizza

The Blue Water Pizza Cafe - Gourmet Pizza

(02) 4929 5686, Queens Wharf Newcastle 2300

going to the NC (Newcastle) for the long weekend.

cruising on the beach, ohh yeah

Yea luckily/unluckily for me my gf went to newcastle Uni for 3 years... involved many a trip to newcastle so i know it fairly well... i have always said if i left canberra i would go there and if there was more IT work i probably would have >_<

yeah i know that place well. never actually been, but my misses is from NC, and she raves about the place.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...