Jump to content
SAU Community

Recommended Posts

hey im pretty happy with my suspension set up at the moment i spose but its just to high, got like 3 inches between my tyres and my wheel arches. If i put bigger rims on they'll fill up the gaurds better but will also make my car higher so.. I spose ill leave the 17's on it and get it lowered. Its a Type-M, so the sides have skirts and are already pretty low, so whats the mimimum distance from ground to kit? At the sides? does the front matter as much? Any other information would be cool, my car looks pretty average at the moment.

Link to comment
https://www.sau.com.au/forums/topic/127904-minimum-ride-height/
Share on other sites

this is such a bullshit law....100mm ride height FULLY LOADED. drive a brand spankin new Clubsport off tyhe showroom floor, chuck 5 average sized adults in it , put some small luaggage in the boot..........100mm? i dont think so! so basically if u buy a brand new car, unmodified, fully loaded u can get d*cked by the cops...so what u do then? rise the stock ride height?

A Victorian TMU car fitted with the FE2 type holden "sports" suspension is under the minimum ride height for victoria at all times regardless of load. The suspension lowers the vehicle to 94mm.

Pity I havent got myself a uniform and a gun...

But, interestingly enough most road worthy testers test the vehicle unladen. The Information from Vicroads does not specify the car must be loaded. It must only clear the height and travel requirements.

I have always explained this to any Police officer who was nice enought to want to look at my car. I also have a print of the Vehicle standards information from vicroads in the car. No where in this entire document does it say i must be in the car.

However... When you are doing this, be nice, professional in your approach and becareful not to be to defiant, you can be charged for failing to obey a policeman.

Unfortunately it is once again a case of a motorist/car owner having to prove themselves innocent by getting a roadworthy from either the police not knowing the law or using their "discretion" and applying penalty where no penalty is due.

You have to remember poor old "johhny copper" here's a thousand bulls**t stories as to why the car is legal. How can he beleive yours?

Either way from their point of view or ours it is a no win situation.

Edited by frx026

frx026 mentions the vehicle being unladen when tested which makes sense as what is the tester going to do, get 4 mates in greasy overalls to jump in the car and test it.

I thought the vehicle had to be no lower than 100mm with 1 adult, might be wrong.

  • 6 months later...

I took my car to pedders, because the rwc guy said i need to lift the car... The pedders guy said my HSD coilovers wont lift much just like 10mms ? atm the lowest point on the car is my zorst thingo... at around 90mm? is the peders guy talking shit or could i lift the car more ?

Edit; btw he told me i need to pay 2 grand to get new suspension ?

Edited by Nefret
  • 4 months later...

I got pulled over the other w/e and when i got rwc my car was sitting around 130mm ? and i have hsd coilovers, the cop put the thing underneath it and my exhaust pipe hit and im like i got it rwc this that i can show u papers his like it doesnt matter we have to check fully loaded 4 passengers with a full tank of fuel ? even thou i got canaried for other stuff the ride height pissed me off... i dont think my car would drop more than 3 cms with coilovers and with extra 150 kilos because i only had 2 mates in the car. :@:@

edit; even if i go to get rwc there goign to check it and its goign to be legal... so double u t f.

Edited by Nefret
You have to remember poor old "johhny copper" here's a thousand bulls**t stories as to why the car is legal. How can he beleive yours?

Pppft "Jonny Copper" can go eat a d|ck. I'm ALWAYS nice, polite and respectable to no avail so I'm over it.

Yes they can ask you to get back in the car as I was. The second time I told him it was 110mm he conveniently didn't have his measuring device..BS!

100mm is the minimum clearance with passengers and full tank of fuel. payload is different, so people saying golf clubs aswell, they cant be counted. in a skyline its 4 ppl and full tank fuel = 100mm ride clearance.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
    • Luckily I didn't put in etch primer as I just found out it's not compatible with my body filler lol. Also just need to sand the panel anywhere between 150-400 grit so I'm in the clear there. It does say to not apply to soft old paint, I assume that means paint that is flaking, peeling,etc
    • @dbm7 and @GTSBoy thank you both very much! will give that a shot!
×
×
  • Create New...