Jump to content
SAU Community

Recommended Posts

Manual or auto?

4S = 4 Door

MT.F5 = Manual Transmission 5 speed

2.5L Turbo (GTT model)

HICAS and rear wheel drive

The accessories need a bit more looking at to work it out, but there are the basics.

Is it possible to know that year my engine was poduced? ( I have only engine, no shell )

Its probably from R33 GTR.

Serial on engine block - rb26 065135a

I've never found a way of looking up engines, sorry.

Hi RANDY,

Somebody ran this VIN for me in http://www.skylinesaustralia.com/forums/topic/391673-pre-purchase-question/page__p__6234999#entry6234999 and it didnt match, however when you ran yours it adds up perfectly. What could be the reason ?

cheers

Hi RANDY,

Somebody ran this VIN for me in http://www.skylinesaustralia.com/forums/topic/391673-pre-purchase-question/page__p__6234999#entry6234999 and it didnt match, however when you ran yours it adds up perfectly. What could be the reason ?

cheers

The VIN you supplied was ECR33 107095, and the VIN in the screenshot that he used was ECR33 010795.

User error =-]

-Steve

Can you FAST an engine number to find out what car it was in?

I don't think you can.

Hi,

Could someone please do this one for me:

6U9000 ECR33-102 247

Thanks!

vpLWsC.png

Can someone please check these two for me, 6U90000ER33052177 and 6U9000ECR33131226. Thanks!

AWyfhg.png

fbtNLi.png

Are you sure you got the first vin right?

Hey Guys,

Can someone please run this through Fast?

6U9000KRS13801052

Its a 180sx..

Cheers,

aBqh3j.png

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
×
×
  • Create New...