Jump to content
SAU Community

VINS you want "fasted"

sewid

By sewid,
in General Automotive Discussion

 Share

Recommended Posts

my_gtr32 Collaborator

my_gtr32

Posted
Posted (edited)
On 13/01/2017 at 4:22 PM, RANDY said:

No probs! Cheers!

Presumably you don't have camber bolts in the struts?

Here are the part numbers for your car, and the alternate part numbers. The other side is 54505 with the same endings.

-Steve

2017-01-13 16_10_49-NFA010 Nissan FAST for Windows [1].png

Thanks Steve for your help. Based on the markings on the LCA's I have, is there anyway to know which is the correct ones?

Also I have noticed the inner and outer ball joints have markings and most likely a certain direction they need to be fitted. The service manual does not tell me much. Any further info in FAST? The outer ball joint has the following markings, 8 7 or L and R. I bet the bloody ball joints are around the wrong way. This would explain the difference in camber. I will check R faces the right side of the car. There are markings on the inner ball joint too. I has the letter B and the other the letter A. No idea what that is all about. I will remove both LCA's soon and double check orientation.

 

Also, can you tell me the part number for HICAS steering rear rack end for my car? BNR32-301183

Cheers Peter

Edited by my_gtr32
  • Replies 4.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

floody
floody

Thanks for that!

(OO)SKYLINE(OO)
(OO)SKYLINE(OO)

Check VIN again, nothing coming up.

sin-
sin-

All R34 GTRs have it except for V-Spec N1 and V-Spec II N1.

Posted Images

RANDY Veteran

RANDY

Posted
Posted
11 hours ago, my_gtr32 said:

Thanks Steve for your help. Based on the markings on the LCA's I have, is there anyway to know which is the correct ones?

Also I have noticed the inner and outer ball joints have markings and most likely a certain direction they need to be fitted. The service manual does not tell me much. Any further info in FAST? The outer ball joint has the following markings, 8 7 or L and R. I bet the bloody ball joints are around the wrong way. This would explain the difference in camber. I will check R faces the right side of the car. There are markings on the inner ball joint too. I has the letter B and the other the letter A. No idea what that is all about. I will remove both LCA's soon and double check orientation.

 

Also, can you tell me the part number for HICAS steering rear rack end for my car? BNR32-301183

Cheers Peter

Hey mate, i'm not sure on what sort of markings are on the parts, but if they look identical from left to right and they measure up the same, it's probably fine. I'm not sure about ball joint direction, other than one is for the left and other for the right. Do you have camber bolts?

Not sure if i've found the part you want:

2017-01-16 09_24_47-NFA025 ILLUSTRATION.png

2017-01-16 09_25_47-NFA010 Nissan FAST for Windows [1].png

my_gtr32 Collaborator

my_gtr32

Posted
Posted
1 hour ago, RANDY said:

Hey mate, i'm not sure on what sort of markings are on the parts, but if they look identical from left to right and they measure up the same, it's probably fine. I'm not sure about ball joint direction, other than one is for the left and other for the right. Do you have camber bolts?

Not sure if i've found the part you want:

2017-01-16 09_24_47-NFA025 ILLUSTRATION.png

2017-01-16 09_25_47-NFA010 Nissan FAST for Windows [1].png

Hi, no the part you looked for is not the right one. I need the tie rod shaft. 48521 is the first bit of the part number. What is the full part number?

I don't have camber bolts but have adjustable upper arms. When I purchased the car the right front wheel always needed the upper arm to be 10mm longer than left to match camber. This screws up caster and ride height. I changed the right arm and now I only have 0.5 degree camber on the right where before it would have been over 2 degrees. That is a huge change so a little variation of the LCA length (from ball joint to ball joint), makes a big difference to camber It measures 315mm on a GTR LCA.

Standard upper arms are 178mm long on a R32 GTR, so if you lower the car to 350mm from hub centre the camber will increase to 1.4 degrees or so. With the right LCA marked 3405U, camber is 0 degree. I have it adjusted as short as possible which is 175mm and I get 0.5 degree instead of almost 2 which you would expect.

I have never heard of any direction the ball joints need to be installed either but why is there markings on them and mention in the service manual that many do go in a certain way. A few millimetres difference in the length of the LCA is all that it takes to resolve the issue. I either have another bent arm (unlikely) or it simply isn't the correct part for a late model R32. All I have to go by is the numbers stamped in the arms. I need to match these numbers with the part numbers you have given me. Nightmare.

Cheers

RANDY Veteran

RANDY

Posted
Posted
2 hours ago, my_gtr32 said:

Hi, no the part you looked for is not the right one. I need the tie rod shaft. 48521 is the first bit of the part number. What is the full part number?

I don't have camber bolts but have adjustable upper arms. When I purchased the car the right front wheel always needed the upper arm to be 10mm longer than left to match camber. This screws up caster and ride height. I changed the right arm and now I only have 0.5 degree camber on the right where before it would have been over 2 degrees. That is a huge change so a little variation of the LCA length (from ball joint to ball joint), makes a big difference to camber It measures 315mm on a GTR LCA.

Standard upper arms are 178mm long on a R32 GTR, so if you lower the car to 350mm from hub centre the camber will increase to 1.4 degrees or so. With the right LCA marked 3405U, camber is 0 degree. I have it adjusted as short as possible which is 175mm and I get 0.5 degree instead of almost 2 which you would expect.

I have never heard of any direction the ball joints need to be installed either but why is there markings on them and mention in the service manual that many do go in a certain way. A few millimetres difference in the length of the LCA is all that it takes to resolve the issue. I either have another bent arm (unlikely) or it simply isn't the correct part for a late model R32. All I have to go by is the numbers stamped in the arms. I need to match these numbers with the part numbers you have given me. Nightmare.

Cheers

yeah wow. What a mess! Good luck with that I suppose!?

 

2017-01-16 14_05_47-NFA010 Nissan FAST for Windows [1].png

  • 2 weeks later...
RANDY Veteran

RANDY

Posted
Posted
44 minutes ago, Giaccovitch said:

Hi could anybody match mine,

BNR32-005619

Engine no. 004051 A

My FAST won't look that up for some reason, but it does show on http://gtr-registry.com/en-bnr32-vin-table.php just chuck the 6 digits in the search box on the right. =-]

RANDY Veteran

RANDY

Posted
Posted
1 hour ago, RANDY said:

My FAST won't look that up for some reason, but it does show on http://gtr-registry.com/en-bnr32-vin-table.php just chuck the 6 digits in the search box on the right. =-]

Fixed it.

2017-02-09 16_52_00-NFA010 Nissan FAST for Windows [1].png

Giaccovitch Enthusiast

Giaccovitch

Posted
Posted
2 hours ago, RANDY said:

My FAST won't look that up for some reason, but it does show on http://gtr-registry.com/en-bnr32-vin-table.php just chuck the 6 digits in the search box on the right. =-]

Cheers mate, is there any way to see what car my engine is from?

RANDY Veteran

RANDY

Posted
Posted
5 hours ago, Giaccovitch said:

Cheers mate, is there any way to see what car my engine is from?

mmm... as in: is it an R33 engine or something... my bro-in-law has that scenario and I think stuff like the oil pump is different and a few other obscure things. I'll have a dig around.

Giaccovitch Enthusiast

Giaccovitch

Posted
Posted
On 2/9/2017 at 11:06 PM, RANDY said:

mmm... as in: is it an R33 engine or something... my bro-in-law has that scenario and I think stuff like the oil pump is different and a few other obscure things. I'll have a dig around.

Yeah not sure what engine it is

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The king 2.0
      Nissan fuga 450gt android screen

      By The king 2.0 · Posted

      Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...