Jump to content
SAU Community

VINS you want "fasted"

sewid

By sewid,
in General Automotive Discussion

 Share

Recommended Posts

my_gtr32 Collaborator

my_gtr32

Posted
Posted (edited)
On 13/01/2017 at 4:22 PM, RANDY said:

No probs! Cheers!

Presumably you don't have camber bolts in the struts?

Here are the part numbers for your car, and the alternate part numbers. The other side is 54505 with the same endings.

-Steve

2017-01-13 16_10_49-NFA010 Nissan FAST for Windows [1].png

Thanks Steve for your help. Based on the markings on the LCA's I have, is there anyway to know which is the correct ones?

Also I have noticed the inner and outer ball joints have markings and most likely a certain direction they need to be fitted. The service manual does not tell me much. Any further info in FAST? The outer ball joint has the following markings, 8 7 or L and R. I bet the bloody ball joints are around the wrong way. This would explain the difference in camber. I will check R faces the right side of the car. There are markings on the inner ball joint too. I has the letter B and the other the letter A. No idea what that is all about. I will remove both LCA's soon and double check orientation.

 

Also, can you tell me the part number for HICAS steering rear rack end for my car? BNR32-301183

Cheers Peter

Edited by my_gtr32
  • Replies 4.9k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

floody
floody

Thanks for that!

(OO)SKYLINE(OO)
(OO)SKYLINE(OO)

Check VIN again, nothing coming up.

sin-
sin-

All R34 GTRs have it except for V-Spec N1 and V-Spec II N1.

Posted Images

RANDY Veteran

RANDY

Posted
Posted
11 hours ago, my_gtr32 said:

Thanks Steve for your help. Based on the markings on the LCA's I have, is there anyway to know which is the correct ones?

Also I have noticed the inner and outer ball joints have markings and most likely a certain direction they need to be fitted. The service manual does not tell me much. Any further info in FAST? The outer ball joint has the following markings, 8 7 or L and R. I bet the bloody ball joints are around the wrong way. This would explain the difference in camber. I will check R faces the right side of the car. There are markings on the inner ball joint too. I has the letter B and the other the letter A. No idea what that is all about. I will remove both LCA's soon and double check orientation.

 

Also, can you tell me the part number for HICAS steering rear rack end for my car? BNR32-301183

Cheers Peter

Hey mate, i'm not sure on what sort of markings are on the parts, but if they look identical from left to right and they measure up the same, it's probably fine. I'm not sure about ball joint direction, other than one is for the left and other for the right. Do you have camber bolts?

Not sure if i've found the part you want:

2017-01-16 09_24_47-NFA025 ILLUSTRATION.png

2017-01-16 09_25_47-NFA010 Nissan FAST for Windows [1].png

my_gtr32 Collaborator

my_gtr32

Posted
Posted
1 hour ago, RANDY said:

Hey mate, i'm not sure on what sort of markings are on the parts, but if they look identical from left to right and they measure up the same, it's probably fine. I'm not sure about ball joint direction, other than one is for the left and other for the right. Do you have camber bolts?

Not sure if i've found the part you want:

2017-01-16 09_24_47-NFA025 ILLUSTRATION.png

2017-01-16 09_25_47-NFA010 Nissan FAST for Windows [1].png

Hi, no the part you looked for is not the right one. I need the tie rod shaft. 48521 is the first bit of the part number. What is the full part number?

I don't have camber bolts but have adjustable upper arms. When I purchased the car the right front wheel always needed the upper arm to be 10mm longer than left to match camber. This screws up caster and ride height. I changed the right arm and now I only have 0.5 degree camber on the right where before it would have been over 2 degrees. That is a huge change so a little variation of the LCA length (from ball joint to ball joint), makes a big difference to camber It measures 315mm on a GTR LCA.

Standard upper arms are 178mm long on a R32 GTR, so if you lower the car to 350mm from hub centre the camber will increase to 1.4 degrees or so. With the right LCA marked 3405U, camber is 0 degree. I have it adjusted as short as possible which is 175mm and I get 0.5 degree instead of almost 2 which you would expect.

I have never heard of any direction the ball joints need to be installed either but why is there markings on them and mention in the service manual that many do go in a certain way. A few millimetres difference in the length of the LCA is all that it takes to resolve the issue. I either have another bent arm (unlikely) or it simply isn't the correct part for a late model R32. All I have to go by is the numbers stamped in the arms. I need to match these numbers with the part numbers you have given me. Nightmare.

Cheers

RANDY Veteran

RANDY

Posted
Posted
2 hours ago, my_gtr32 said:

Hi, no the part you looked for is not the right one. I need the tie rod shaft. 48521 is the first bit of the part number. What is the full part number?

I don't have camber bolts but have adjustable upper arms. When I purchased the car the right front wheel always needed the upper arm to be 10mm longer than left to match camber. This screws up caster and ride height. I changed the right arm and now I only have 0.5 degree camber on the right where before it would have been over 2 degrees. That is a huge change so a little variation of the LCA length (from ball joint to ball joint), makes a big difference to camber It measures 315mm on a GTR LCA.

Standard upper arms are 178mm long on a R32 GTR, so if you lower the car to 350mm from hub centre the camber will increase to 1.4 degrees or so. With the right LCA marked 3405U, camber is 0 degree. I have it adjusted as short as possible which is 175mm and I get 0.5 degree instead of almost 2 which you would expect.

I have never heard of any direction the ball joints need to be installed either but why is there markings on them and mention in the service manual that many do go in a certain way. A few millimetres difference in the length of the LCA is all that it takes to resolve the issue. I either have another bent arm (unlikely) or it simply isn't the correct part for a late model R32. All I have to go by is the numbers stamped in the arms. I need to match these numbers with the part numbers you have given me. Nightmare.

Cheers

yeah wow. What a mess! Good luck with that I suppose!?

 

2017-01-16 14_05_47-NFA010 Nissan FAST for Windows [1].png

  • 2 weeks later...
RANDY Veteran

RANDY

Posted
Posted
44 minutes ago, Giaccovitch said:

Hi could anybody match mine,

BNR32-005619

Engine no. 004051 A

My FAST won't look that up for some reason, but it does show on http://gtr-registry.com/en-bnr32-vin-table.php just chuck the 6 digits in the search box on the right. =-]

RANDY Veteran

RANDY

Posted
Posted
1 hour ago, RANDY said:

My FAST won't look that up for some reason, but it does show on http://gtr-registry.com/en-bnr32-vin-table.php just chuck the 6 digits in the search box on the right. =-]

Fixed it.

2017-02-09 16_52_00-NFA010 Nissan FAST for Windows [1].png

Giaccovitch Enthusiast

Giaccovitch

Posted
Posted
2 hours ago, RANDY said:

My FAST won't look that up for some reason, but it does show on http://gtr-registry.com/en-bnr32-vin-table.php just chuck the 6 digits in the search box on the right. =-]

Cheers mate, is there any way to see what car my engine is from?

RANDY Veteran

RANDY

Posted
Posted
5 hours ago, Giaccovitch said:

Cheers mate, is there any way to see what car my engine is from?

mmm... as in: is it an R33 engine or something... my bro-in-law has that scenario and I think stuff like the oil pump is different and a few other obscure things. I'll have a dig around.

Giaccovitch Enthusiast

Giaccovitch

Posted
Posted
On 2/9/2017 at 11:06 PM, RANDY said:

mmm... as in: is it an R33 engine or something... my bro-in-law has that scenario and I think stuff like the oil pump is different and a few other obscure things. I'll have a dig around.

Yeah not sure what engine it is

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      New R32 owner soon

      By joshuaho96 · Posted

      Hard to say, just pop the rocker covers off and have a look if you think it's cammed. You probably need to replace the valve cover gasket/half moons anyways.
    • niZmO_Man
      R32 Nostalgia

      By niZmO_Man · Posted

      From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 😢 
    • niZmO_Man
      New R32 owner soon

      By niZmO_Man · Posted

      Remember this is 1988 tech.
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • Duncan
      1992 R32 GT-R Race Car

      By Duncan · Posted

      heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
×
×
  • Create New...