Jump to content
SAU Community

Recommended Posts

What is the best method/product for cleaning brake dust and other assorted crap off of this type of wheel? As you can see I haven't been able to master the tecniques required to get into the bits behind the spokes (read: I'm too lazy to do it with a toothbrush and take all day). Is there a chemical thats designed to get rid of this grime, but not the paint or anything else?

Be nice to the newbie. :)

Link to comment
https://www.sau.com.au/forums/topic/129019-how-to-clean-spoked-wheels/
Share on other sites

There is an eagle 1 tyre and wheel cleaner, ive used it a couple of times on my rims, but i dont usually do behind the spokes. Not too sure if this stuff is suitable to painted rims, but ive got shadow chrome and they seem fine after a few uses.

Evil

We have this stuff at work called Acid Klene its about $200 for a 20L drum and I just spray this straight onto my rims then rinse off with the high pressure hose and they look brand new gets rid of ALL the brake dust, its amazing how well it works, have used it on many friends cars and their shocked with how well it works, im not sure if its available through any shops though? We get it through a company called Jasol,

I guarentee this would work just be careful if you manage to get a hold of it because if you breathe the fumes from it in you will get high as a mofo.

Edited by Dave69001

All I use is plain water and an old rag, it gets all of the grime off. But I have to clean my rims every week as I have white rims so as long as I keep it up I don't need anything harsher. They are 6 spoke, nothing as insane as the ones you are trying to clean.

I use the Zymol wheel cleaner with the little brush - smells kinda minty.

I've got wheels with studs around the dish so can be hard to clean properly without a little assistance. But the brush makes the job pretty easy...

Works well for me...

http://www.zymol.com.au/products/productde...p?pid=2&p=1

buy some new rims that are eaiser to clean.... :)

like warren said, head to supercheap, ive been using kitten and armourall wheel cleaners, spray on hose off sparkle sparkle easy as, just do it often so the dust dosent collect

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...