Jump to content
SAU Community

Recommended Posts

the series 1.5 came out in 95 only i believe - check your coil packs and follow the plugs that plug into them. If it plugs into a square box that has another plug connected to it going to the engine harness then its a series 1 engine.

If its just pluged into a plug with no square box then its a engine wich is a mix between series 1 and series 2

Its got coils with ignitors built in and it does not have a plastic front wheel on the turbo but still has ceramic rear (same as series 1 turbo)

well my car is a r33 series 1 style ....but it has the series 2 motor in it , the car was made in late 1994....so what have I got a series 1 or 2 ...or the rare SAU 1.5? hahahahah

.....oh this is the motor which was made with the car! not dropped in after!

they do

yeah i thought series 1 had variable cam timing too.

also this tps plug not used on S1 manual, but is used on S2 manual. Dunno if that applies in the R32 setup though.

post-29392-1154923525.jpg

Edited by Munkyb0y

thats a series 1 motor. series 2 have a rounder tps, and it has 2 plugs (although both not always connected).

as for the series 1.5, they weren't a true model, but just a mix match. they have a series 2 wing, series 1 interior, series 1 bodykit, and most have a series 2 motor, drivers airbag as standard.

Edited by mad082

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...