Jump to content
SAU Community

Recommended Posts

Yes I'm bored.. though at some stage I'm going to purchase an automatic luxo cruiser 2nd car

I quite fancy these two:

What do you guys think would be the better sleeper and best all rounder etc

Toyota Aristo 3L TT

1.jpg

Mitshubishi Legnum 2.5L T 4wd

1.jpg

(would have to be full leather interior of course)

The 2Jz is kind of hard to look past, although with the 4wd of the legnum I'm not sure which would be the fastest.

Edited by CONRAD
Link to comment
https://www.sau.com.au/forums/topic/129671-luxo-sleeper-aristo-or-legnum/
Share on other sites

I agree the Legnum looks better, and sure the Galant is great.. though getting owned by a wagon is waay more sleeper.

My only concern would be how difficult it is to mod the mitsubishi compared to the 2jz which workshops have had planty of experience with and the fact that the engine is bulletproof.

your gtr back on the road yet conrad? as for either of the cars, i'd go the legnum. i dont know how luxo it is though.

hey, not really.. I sold the car to a friend, whom put his own 33 gtr engine he had into it, I was actually contemplating buying that engine though lucky I didn't as it went pop a few months down the track. So no Nissan's for me, though I picked up a cheap FC and rebuilt that as a change.

Edited by CONRAD

I'd go the aristo myself. The office at j-spec is divided on the issue :) half of us want twin turbo sedans, the other half want legnums or galants... and one monkey in the office wants a V8 aristo with AWD... although... I'd be getting the AWD V8 aristo, takin out the V8 engine and puttin in the 2jz :O oooo yeah! giggety giggety!

They don't come in a manual version, but we are finding a few that have been converted. Because its not a factory option, each manual that we come across HAVE to be thoroughly inspected, to check if the quality of the conversion is done professionally using factory parts etc, or a hack n slash kinda job. Once the inspection is done, the photos and report are sent to the compliancer who will carry out compliance on the car... only if they agree to comply the car do we go ahead with the purchase.

Basically its a bit of a headache... it'd be so much more hassle free if the conversion was done locally after the car was complied n registered.

The aristo is by far the classier car. Its got a better engine too. Over here in NZ there a millions of turbo legnums and they arent really up there spec wise.

You could also try a nissan cima with a 4.1L V8 or a turbo leopard or a turbo gloria/cedric or even turbo laurel

Cima:

19978901_full.jpg

gloria:

21539337_full.jpg

Edited by GorGasm

Bring on the legnum.

I love the jaggered looks of the legnum, the aristo is too like, rounded.

Still take a stagea over a legnum any day of the week though, but for what they are/cost, they are nice cars. Must get the manual though, the tiptronic boxes are very breakable so ive heard.

PS. The best sleeper? Id get the legnum mate, nothings as good as a hard 4wd launch to surprize your enemy, and it sure helps in the twisties.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...