Jump to content
SAU Community

My Car Goes Faster Now Because....

Topaz

By Topaz,
in WA Wasteland

 Share

Recommended Posts

mitchy_ Grand Master

mitchy_

Posted
Posted

going off your logic tom, my gts-t should leave you in a trail of smoke (and not just overfueling either)

i have 12 stickers beeyotch.

then there is the racing stripes, i think i might have the fastest r33 in all of perth?!

ossie_21 Grand Master

ossie_21

Posted
Posted

My hp sticker list*:

2x GReddy stickers on front bar to help brake cooling

2x Rays Engineering stickers on front bar to optimize air fuel ratios

4x Import101 stickers (front & rear windscreen, 2 quarter windows) to spool the turbo faster in the lower rev range

2x SAUWA stickers on the quarter windows to provide additional downforce at speed

2x skylinesaustralia.com stickers on the rear spoiler to provide better traction in wet conditions

oh and

1x HKS sticker to cool the air entering the engine a further 10%

*these may or may not entirely help car performance

  • 2 weeks later...
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...