Jump to content
SAU Community

Recommended Posts

  • Replies 418
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I'd hate to see your high volume ones... well... actually i've seen supposedly two of them.

And one was hugging the bowl :)

if i rember corectly you were chucking it up in the dunnies and i was sober enough to knock back a shag fom a fat chick

so we still had 40 beers before we were pissed

im in just to slap nismoids arse a few times pretty boy

Well,

I have sat on the side line for a while on this one.

GOD DAMM! A Wednesday? you know how to entice people dont you!

Im a maybe definite but could be a perhaps not sure little chance almost 100% going to be there!

Everyone get that.

My 10c is that if any car from Sydney gets within 5 seconds of the quickest 2-3 Vic GTRs then they are doing a pretty good job.

I will be happy to get the feck out of no good Victoria. NSW cars are cursed down here :D

Roy, thats a big call, the guys need to run almost V8 super car times to be 5 sec better.

My light tuned GTR has hits the 1.09's so they better be coming to drive hard!

check that

4 way with a fat chick

I was about to say... dont tell me finer details had been forgotten.

And mark was off his chops. Dont put the "we" in there, he chundered in that club after the pub :P

Well,

I have sat on the side line for a while on this one.

GOD DAMM! A Wednesday? you know how to entice people dont you!

Im a maybe definite but could be a perhaps not sure little chance almost 100% going to be there!

Everyone get that.

Yeah mate a Wednesday, should be PLENTY of track time for the $$$

Hahaha, you've confused me with the

Im a maybe definite but could be a perhaps not sure little chance almost 100% going to be there!

but ill assume you're in :)

Roy, thats a big call, the guys need to run almost V8 super car times to be 5 sec better.

My light tuned GTR has hits the 1.09's so they better be coming to drive hard!

Like i said, 5 seconds :)

Im hoping to be doing 1:08s in my car, though i will happy with a 1:09. There are cars coming that have done 1:06s in the damp with only a few laps under their belts. Hell even Snowball did a 1:07 with a crook engine. So like i said, andyone getting within 5 seconds of them will be doing well. As im guessing there will be cars doing 1:04s and 1:05s :)

Friggin cheater cars, i remember when a 1:10 was quick at Wakefield because noone ran mods and semi slicks ;)

BUT, who really cares. Let shope we get a good number of ppl out having a good time...and we are able to witness some top notch cars crank out some scary speeds. I know im goignt obe there with a video camera to catch it all.




  • Similar Content

  • Latest Posts

    • Kittens in first to claim dominance of the residence, then puppies later From past experience, the other way around can be problematic to say the least  Those weird "Dobby looking"  little kittens are not cheap....LOL
    • At least yours have parkour down pat. One of mine will still trip over his own shadow and fall over... He's a special type of cat... Ha ha ha
    • The question then becomes - was there any fluid coming from that hole before you did the rebuild ?    You may not have noticed, of course.   Depending on how you did the rebuild, the possibility has to be considered that somehow (cleaning ?)  fluid entered that hole and is now being 'forced'  out by small movements of the proportioning valve.   From the factory, there's actually a small rubber plug in that hole but with age and under-bonnet heat it's quite common for it to 'go missing'.  That rubber plug is designed to allow the venting process but also to prevent 'stuff' getting to the area (prevent corrosion, etc).   The plug is also not available as a spare part AFAIA. Personally I wouldn't race and buy a new master just yet but keep an eye on the area to see if the 'leak' continues.   If you're concerned about brake fluid damaging nearby paintwork, cable tie a piece of suitable absorbant material over the hole and remove/monitor occasionally.    Operation of the proportioning valve and the brake master itself won't be affected, but also keep an eye on brake fluid level, of course. In terms of a new master, the genuine part is getting expensive, unfortunately.  Amayama is showing AUD900+.   I was searching recently and there's an aftermarket part available from Japan made by 'Parts Assist': https://zenmarket.jp/en/yahoo.aspx?q=BNR32%2bBM50&p=1 Whether it's any good I have no idea, although in my experience Japanese aftermarket stuff is pretty good quality-wise.   The above site allows overseas buyers to purchase stuff more easily from Japan but there are fees and shipping costs, of course.   The original Japanese seller page is here: https://auctions.yahoo.co.jp/jp/auction/p1197401228 Copper/Nickel is fine but I still prefer bundy tube and it's also cheaper.
    • Your chihuahuas look weird!
×
×
  • Create New...