Jump to content
SAU Community

Recommended Posts

Hey everyone,

I have the rad removed from my car and the head its ready to be removed. I am not wondering how i go about removing the crank pully.

all the belts are loose and now i just need to get the timing belt off.

I am aware that the bolt will be torqued to 340 ft/lbs.

Now what i need to know is what size is the head on the crank bolt and how to i stop the engine from rotating around.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/131754-crank-pully-removal/
Share on other sites

the usual way to get these bolts cracked is to have a breaker bar kind of wedged onto the ground and then cranking your motor. that will loosen the bolt. its 27mm from memory.. if not that its 24mm.

you could probably get a long breaker bar and lever it off. you can probably stop the engine from turning by sticking it into 1st. someone will correct me if im wrong.

4th will be harder to crank because it's a taller gear, if you're using the engine-crank method, then 1st is the go. And only for one second.

After the bolt is off, you'll probably need to use a puller. There are two different types. One has arms that pull on the outer lip of the balancer, and the other uses the two spare holes in the balancer for leverage. Both use a big bolt that pushes into the centre where the nut was removed.

The first type actually broke my balancer in three places, the second one worked but was much harder to wind on.

And if its already out of the car, 2 flywheel bolts back, a pry bar between wedged against the engine stand.

Then big socket, breaker bar and the longest strong pipe you can find over the end, those galvanised fence posts work a treat. Pull until bolt comes undone or socket breaks. If 1 sit down and have a beer, if 2 buy a new stronger socket

Once thats done you need a balancer puller to pull it off....bolt back in loosely, screw 3 bolts into the holes in the balancer and screw it off slowly.

After that is the timing belt gear which is the same again, a puller over the top and some patience.

If you only want to take the head off, the simply remove one of the cam wheels (exhaust is easier).

If the crank bolt is NOT 27mm, then it's the wrong bolt! It's been 27mm since 1968!

If you're using the engine-crank method, then you don't want the gearbox in any gear, unless you want the car to launch through the back wall of the shed.

If you only want to take the head off, the simply remove one of the cam wheels (exhaust is easier).

If the crank bolt is NOT 27mm, then it's the wrong bolt! It's been 27mm since 1968!

If you're using the engine-crank method, then you don't want the gearbox in any gear, unless you want the car to launch through the back wall of the shed.

Haha very funny. I was thinking the same. To replace the cam gears first install the inlet gear and fit belt then set belt on exhaust gear and work it accross until it slips onto the end of the cam shaft. Use patients and you will get there. The 2nd time i did mine thats how Geoff showed me to do it!

If you only want to take the head off, the simply remove one of the cam wheels (exhaust is easier).

If the crank bolt is NOT 27mm, then it's the wrong bolt! It's been 27mm since 1968!

If you're using the engine-crank method, then you don't want the gearbox in any gear, unless you want the car to launch through the back wall of the shed.

GTR bolt is 30mm....

ran into a slight problem.

i went to go put the m6x1.00 bolts into the crank pully and it turns out the last person who pulled the pully off broke a m6 bolt on in it.

so now i have one bolt hole.

What am i to do now?

i sure as hell do not want to removed my entire front end.

yep yep... Dunno where I got that from! Thanks for being so harsh, grigor.

I certainly didn't have mine in any gear when I cranked the motor over.

The second time we pulled it off, we had it in 4th (as I said was correct, btw) and the breaker bar did it for us.

I guess i'll try and redeem myself from the 1st gear thing and add:

Unplug CAS when cranking over so the motor doesn't actually start. I know your motor is out of the car, but just incase someone tries this "in-car".

Also, don't lose the locator. It's a small semi-circle of metal about 5mm wide. It'll probably fall out when you finally get the balancer off!

Edited by RANDY

Hey I'm a cranky old fart.

When ever I see guys using the starter to remove the balancer bolt I go Ape.

There's a rough way and there's the correct way to do a job.

Like removing the master pins from crawler tracks with a jelignite gun.

It gets the job done but it's just plain stupid.

Also, don't lose the locator. It's a small semi-circle of metal about 5mm wide. It'll probably fall out when you finally get the balancer off!

yep. woodruff keys arent something you want to lose. there are 2 of them. put them somewhere safe.

There is one locator as the crank pully only has a location for one.

Also i used a 4 inch 3 arm puller and a can of wd40 and took my time and slowly pulled it off watching the rubber inside very very closely.

Also the crank bolt was not on tight at all, kind of scary how loose it was.

I removed it testing to see if the clutch would be holding then i slipped and cracked the bolt with a standard 1/2 inch socket :ninja:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...