Jump to content
SAU Community

Recommended Posts

Hi everyone just need your help have searched the forum n tried, what could be wrong with my r33 gtst series1. I was driving just cruising around on a hot victorian day, when slowed down to stop on a traffic light my car suddenly stop running, all the power lights still running stereo on and nothing that would suspect its the battery. Jump start it no go. Push start it again n again no go. den went n bought a new battery with 470cca on it, still no go. when I turn the ingnition on I can hear the fuel pump priming, then turn key all the way to start, all i hear is just a click, dash lights dim then nothing not even a crank just a click.Ive checked the crank angle sensor, afm (cleaned), push all the plugs making sure they are connected properly, tap the starter motor with a hammer,checked all the fuse in the car, boot, and front engine but all is fine and still no go. what could be wrong. Here are my mods fron mount, piggy back fuel controler(e-manage), boost control 10psi, changed my ignition to a waste spark. Please help!!! THANKS

Link to comment
https://www.sau.com.au/forums/topic/138661-help-car-wont-start-whats-wrong/
Share on other sites

But there's still power. Headlights n interior lamps work all electronic works, put in a new battery with 470ccamps on it but still doesnt start. tried push starting it no go, jump start it still nothing all I hear is a click thats it no crank or anything its not turning over....

But there's still power. Headlights n interior lamps work all electronic works, put in a new battery with 470ccamps on it but still doesnt start. tried push starting it no go, jump start it still nothing all I hear is a click thats it no crank or anything its not turning over....

If thats the case it has to be the starter motor its prob seezed up on you or something, when you try to push start it does it try to crank over if it does your starter motor shouldnt be seezed it would be an electrical prob.

good luck with that.

Yeah I was thinking maybe the igniter does'nt work cuz of my waste spark set up. But why does'nt it crank. I can hear a click but that's it. Does anyone know how to check the ecu error code. Sorry guys but realy desperate here!! Thanks for the replies

Does anyone know how to check the ecu error code. Sorry guys but realy desperate here!! Thanks for the replies

You have to get the car to a workshop with the computer to plug into the car to read the error code as far as I am aware unless there is an aftermarket tool to do this?

Probably easier and quicker cause of time of day that you call the NRMA or local motoring group in your state and get them to come out and check it out.

Drew.

if it clicks and doesn't turn over the starter isn't working, either because it is dead, its not getting enough power (battery or alternator), or it's relay is stuffed.

Pull the starter off, clutch start it down to an auto electrician and get them to check the starter and its solenoid.

yeah id guess starter motor. only problem i had with that was i had to have mine rebuilt. couldnt find a second hand one. still only took a day for my mechanic to take it out, send it away to be rebuilt and put it back in. think it was $260 all up.

this sounds like a starter motor. because the click you hear when you turn the switch is the start relay cliking. but then again why would the car die in mid traffic?? i mean the starter doesnt run while youre drinving. have you ignition cheked, look into your rebuilded ignition setup, maybe somthing wanst hooked up properly. When i tell people to stick to their stock type ignition systen ie the 6 coil setup, they ont tend to listen.

gday

you could have blown a fuse?

thats what happened to me i was at a stop sign and then my car just died, i tried to clutch start it but it had no effect, later on my mechanic said i had blown a fuse.

so why dont you check that out.

hope this helps, goodluck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...