Jump to content
SAU Community

What Has Gone Wrong With My Rb26?

NismoR31Jet

By NismoR31Jet,
in Engines & Forced Induction

 Share

Recommended Posts

NismoR31Jet Community Regular

NismoR31Jet

Posted
Posted

Well, I was at sandown today giving the car its first track day with the 26. After one hard lap things looking bad. At full throttle above 6000 RPM the oil pressure would go from around 70 psi down to 50 and then start to fluctuate from 50 to 25 or so until I back off the gas and bring the revs back down to below 6 grand. Then after this happened twice I pulled into the pits and saw oil leaking from a cooler pipe. I removed the cooler pipe right infront of the plenum to find the plenum and cooler piping with a thick coating of oil in them. I am sure this oil is just blow by, as the engine has around 80,000 kms on it, but the swinging oil pressure has me baffled.

The engine itself is stock from an R32 GTR, with a High energy trap door baffeled sump, cam gears, power FC, rebuilt with steel wheel turbos, 3 inch exhaust and running around 15 psi it was making just under 270rwkw.

I now have the car home, it seems to be running fine but blowing a bit of white smoke, this could be from the oil in the cooler and piping tho. Oil is Mobil 1 5w50 and level is spot on.

What is your take on this, what can you see causing the oil pressure fluctuation?

I think a rebuild will need to be done, so now I need to work out what sort of rebuild do i want!

Link to comment
https://www.sau.com.au/forums/topic/138753-what-has-gone-wrong-with-my-rb26/
Share on other sites
T04GTR Grand Master

T04GTR

Posted
Posted
I now have the car home, it seems to be running fine but blowing a bit of white smoke, this could be from the oil in the cooler and piping tho. Oil is Mobil 1 5w50 and level is spot on.

thats the problem!!

gtr sumps are crap. you need to overfill them by about 1.5-2L for the track to stop OIL SURGE.

NismoR31Jet Community Regular

NismoR31Jet

Posted
  • Author
Posted
thats the problem!!

gtr sumps are crap. you need to overfill them by about 1.5-2L for the track to stop OIL SURGE.

It isn't a GTR sump, but a High Energy trap door sump.

I have been told i may need restricters in the oil gallery to stop the oil from gathering in the head?

HRthirtyone Rising Star

HRthirtyone

Posted
Posted (edited)

could be rings or turbos, but if turbos were recently rebuilt, its prolly rings. do a compression test to see if you cracked a piston or something. it may still feel like its got all the power there and runs fine, but still have something really wrong with it.

all depends on how much oil your loosing into the pipes. also dont the older rb26 oil pumps tend to give up with lots of high rpm?

Edited by HRthirtyone
NismoR31Jet Community Regular

NismoR31Jet

Posted
  • Author
Posted

Yep, I just read the 5 page thread on oil control by Sydney Kid. It seems to make a lot of sence, I guess all the blow by could be caused by the oil pooling up in the head?

I guess the oil control mods outlined in that post should be done, it can only help.

Yea ash, I will speak to benno tomorrow and suss it out. What bothers me is until I noticed the gauge I was pushing up to 7,500 a fair bit, so I am thinking I should replace the main and big end bearings just to be sure. And if I am doing the bearings I probably should to an R33 crank or fit the oil pump drive collar and a better oil pump while I am at it.

And then while I am at it I may as well re ring it or fit forgies, and the turbos will be off.....so a set of GTrs? turbs may find their way on too.......

Now do you see my problem? I have an ilness.....I am a modificationaholic.....I need help......

But my wife is encouraging a build.......so this is looking to be messy.....

700HP-GTR33 Mentor

700HP-GTR33

Posted
Posted

Have you changed the oil pump?

Did you install the cooler?

Do you have a catch-can?

I had my front main seals changed 3 times before I gave the mechanic a N1 oil pump.

I was also having oil pressure problems.

Luckily for me I had acted at the right time, the screws were nearly about to fall off.

Sometimes too there could be a blockage in the line, rare as it seems, some have been unlucky.

Get everything checked out before you go out again. or you may have to build quicker than you thought...

Hope I have been of some help.

Cheers :P

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

John - i know your issue, i have the same illness :P

Just remember, once its apart, it never ends cheap and it will cost you 5 figures end to end.

IMO - if the motor isnt dead and you check it out and its ok, dont touch it.

You have the steel wheels in there so you dont have the danger of it letting go. Just wait till it dies then pour the cashola into it.

Motors take a matter of weeks to be done, so its not like when it does die.. you'll be without a car forever

NismoR31Jet Community Regular

NismoR31Jet

Posted
  • Author
Posted

I hear where you are comming from man.

I am just worried I may have done some damage to the bearings with the oil pressure dropping at the revs I was pulling.

What engine is yours? Or more importantly, what crank and oil pump you using?

In the back of my mind there is the fact that mine is an R32 engine, and they are known for dodgy oil pumps.

I just want to make it reliable....

700HP-GTR33 Mentor

700HP-GTR33

Posted
Posted
I hear where you are comming from man.

I am just worried I may have done some damage to the bearings with the oil pressure dropping at the revs I was pulling.

What engine is yours? Or more importantly, what crank and oil pump you using?

In the back of my mind there is the fact that mine is an R32 engine, and they are known for dodgy oil pumps.

I just want to make it reliable....

Hello again,

All RB motors have a potentially dodgy oil pump, RB26 out of a 32 has a greater chance due to its age.

If you want to do track work safely ,get a larger sump and as Ash has stated, get some restrictors to stop the top from getting to much oil.

As you are getting a larger sump get the oil and water pumps. Jun oil pump with collar if you are really serious. Also get the Bearings ,Bolts and timing belt changed .

Then you might have a reliable car :laugh:

There are too many things that can go wrong with the RB26 motor....if not looked after properly.

The supporting mods. are endless but the Mod itself must be maintained for it to work.

Anyway like you and Ash, I too am a modoholic (?) .

Thus, I am on SAU to navigate my next steps. :)

Cheers and good luck :)

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
I hear where you are comming from man.

I am just worried I may have done some damage to the bearings with the oil pressure dropping at the revs I was pulling.

What engine is yours? Or more importantly, what crank and oil pump you using?

In the back of my mind there is the fact that mine is an R32 engine, and they are known for dodgy oil pumps.

I just want to make it reliable....

You know what mine was, i did buy it off your cousin :wave:

Was a 32 motor, but obviously did the collar and what not as part rebuilt, and an N1 oil pump. Virtually the same as my 25 rebuild but in the 26!

Is there a was to check if you have done any damage? Ive got no idea on that one... if there is then that could save you some heartache.

Risking Grand Master

Risking

Posted
Posted

An oil pressure guage can give you a little indication of bearing wear.

Also you could look into an oil evaluation which can also give you a fairly accurate indication of bearing condition etc.

By far the best way is to pysically hold them in your hand and inspect them though.

Personally if its not rattling and carrying on id keep using it till she displays symptoms of bearing wear etc.

NismoR31Jet Community Regular

NismoR31Jet

Posted
  • Author
Posted

HAHA.......

After havin a chat with benno I am going to rebuild it regardless, as far as I know from what the inporter told me, it has 80,000 kms on it.....although....he also told me it was an R33 engine.....which it is not!

So yea....it is running fine now but it has got a fair bit of blow by, so might as well get it all sotred in one hit.

rob82 Mentor

rob82

Posted
Posted
You know what mine was, i did buy it off your cousin :)

Is there a was to check if you have done any damage? Ive got no idea on that one... if there is then that could save you some heartache.

Remove the oil filter and peel it open with a stong can opener and see if there is any copper coloured material within the filters.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • JC71
      gauge needle removal

      By JC71 · Posted

      okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Cheers mate. Seems some people get lucky others don't. It looks like the motor was detonating (to be expected if it was overboosting I suppose) as the pistons had a lot of detonation damage, and the bearings were stuffed. The bores were very scoured too, not sure if that's from the pistons or bits of ceramic turbo. By the by now. Have been trying to avoid the rabbit hole too much on the rebuild, and there's been a few hurdles along the way, but with any luck I'll have the car back soon™. Might even pop up a thread then.  
×
×
  • Create New...