Jump to content
SAU Community

Recommended Posts

Hi All,

I thought i would come to the experts. My RB20 is coming along nicely with a APEXI AVC-R boost controller, fuel pump, coil packs, air induction and full exhaust system and I love the results. On the weekend however I put on a new BOV and I noticed my oil pressure idleing is just above the zero and when boosting wont go above 2 (which is a quarter of the maximum 8). Why is this and would it be due to the BOV? Also how can this be tested or fixed.

I appreciate any help as I have not come across this before.

Link to comment
https://www.sau.com.au/forums/topic/139833-oil-pressure-low-on-my-rb20/
Share on other sites

Hi All,

I thought i would come to the experts. My RB20 is coming along nicely with a APEXI AVC-R boost controller, fuel pump, coil packs, air induction and full exhaust system and I love the results. On the weekend however I put on a new BOV and I noticed my oil pressure idleing is just above the zero and when boosting wont go above 2 (which is a quarter of the maximum 8). Why is this and would it be due to the BOV? Also how can this be tested or fixed.

I appreciate any help as I have not come across this before.

the senders normally whack out... but in my case i think my oil pump is screwed because the top end is making horrible noises.

I have an Autometer gauge which has replaced the stock oil pressure warning light sensor. It reads in PSI so i dont know if it will be any help to you but i use a 10-40 Motul oil in my RB20DET which is basically stock, on cold start i get around 60-70psi of oil pressure at idle, after around 5-10mins of driving it will read around 6-15psi of pressure at idle and rise to a max of around 45-50psi at 3000rpm when hot.

stupid question, but will pressure vary b/w oil?

i just changed my oil from a motul 4100 turbolite 10w-40 to motul 8100 xcess 5w-40 and ive noticed a pressure drop once the oil is warm. Previously it would sit close to 4 on the guage and no it doesnt rise above 2 once warm..

should i get a different oil?

engine is an rb20det btw

i got custom gauges put in, and my car on 15-50 mobil one, reads about 70 cold, and about 40 @ 3000rpm, but ideling it sits between 20-15 psi should i be worried can suply photos.

Note: mine did the whole read jsut above zero never gets above 2 thing, so i went out a put customs in

- to answer your comment, get ur mechanic to do an oil pressure test on it, and i would recommend getting aftermarket gauges, and leave the BOV out of it.

55yko

Edited by 55yko

as long as the oil pressure warning light is not illumminated, then all is ok

the stock oil pressure sender is dodgy on all nissan imports and won't give you anything even close to the correct pressure...

i recently installed an aftermarket gauge in my glovebox and find that:

when warm at idle it sits between 1-2bar

when warm and cruising/driving the oil pressure varies with rpm (can't see this on the stock gauge) and sits up around the 3-4bar area

obviously pressures are much higher when the oil is cold

gauge cost me $20 (ebay)

gauge cup $5 (ebay)

sandwich plate $30 (justjap)

not a bad investment and is hidden in the glovebox nicely :(

cheers,

Warren

My stock guage is all over the place.

Some days it reads like it should, others barly above the 0.

Its always been like that though, even with the old motor.

Quite funny actually as I've caught it going from crappy to normal.

Cruising along at 100km/h, oil pressure sitting on around .5 then all of a sudden with a sharp jolt the needly flicks up to just over 4 which is where it sits when the guage is playing nice, sat there for the next few days then decided to go gar gar again.

Wouldn't be too concerned. RB20's are cheap anyway, drive it until she starts making funny noises.

Guilt Toy.... I'd say your lifter problem was likely attributed to poor oil pressure. As I'm sure you already know. :P

Thanks for all your help everyone. I'm just going to drive the bloody thing and have a mind set that the oil pressure gauge is faulty. If it goes boom I will just chuck a RB25 in it anyway as I planned on doing next year anyway.

hi im wondering if anyone could help me on a simalr topic?

i have a problem with my rb26 regarding with the oil pressure, everytime i hit high revs or hit boost the oil pressure goes down to 0 and the warning light will turn on.

if i drive normally without going over 4-5000rpm its ok, the pressure doesnt drop and the warning light does not turn on.

i would appreciate any help thanks.

cheers,

hi im wondering if anyone could help me on a simalr topic?

i have a problem with my rb26 regarding with the oil pressure, everytime i hit high revs or hit boost the oil pressure goes down to 0 and the warning light will turn on.

if i drive normally without going over 4-5000rpm its ok, the pressure doesnt drop and the warning light does not turn on.

i would appreciate any help thanks.

cheers,

Jesus, stop driving it on boost. High revs + no oil pressure = boom, as said above the warning light almost always does work. It could just be low on oil and getting starved under decent Gs (accel, cornering) check the level and if its really low do a change, otherwise it could be the pump itself but definately check it out before you do any more damage. Also there can be problems with excessive oil getting to the head but I don't really know much about this topic. Probably be wise to check the oil and see if theres any bearing matter in it as well (silver sparkles)

Edited by Rolls

will the engine die straight away if your on boost with no oil pressure?

or is it more of a wearing of the engine until it dies?

i think ive been hitting boost with no oil pressure

hopefully its just a tired guage

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...