Jump to content
SAU Community

Recommended Posts

When are you gonna get Dyno'd? I'll talk to Robbie for you and see if you can get it done for cheap. All you need is power runs, don't you? I've been meaning to get a base power run for mine before the new engine goes in.

Yeah we went to adrenaline, just rocked up to try our luck but he said there pretty busy for the next week (till thursday)

So might try and book it in for saturday. Yeah just need a power run to see where its at

just had adrenaline retune my car with new turbo installed, must say rob does a good tune each time! great results as well verry happy will be much more fun at the strip this time around when the dam rain pisses off!!!!!!!!!!! hopfully the 25th of this month will see us all out there haven a few runs. them all these bloody holden and ford lovers can bowe down to the rice burners!!!!!:worship: ha ha ha ha jokes jokes there are a few fast ones around thats for sure, stupid xr6t! little modes and big power out :banana:

ill be in for any cruize any time!!!!!!!! any excuse to go for a drive, and the tune ended up at 492rwhp so far a little more in refining the tune and should be maybe a little more in it. ran out of fuel in the injectors so that will be the next thing. car drives great so far so will be keen to do some 1/4 mile times. i got slicks this time and changed the rear diff ratios so should be a bit more fun

well that depends on what turbo your running at 18psi? still will be good figures, it will be more responsive than me on the road thats where is counts. not that mines a huge lag monster but the 3076r garrett i had earlyer this year was a ball tearer!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...