Jump to content
SAU Community

Recommended Posts

What happened at last years easter meet i don't remember :woot:

shit got loose, we have to try and organise something again before next year.

give me a call when you want to come get your new skid rig

shit got loose, we have to try and organise something again before next year.

give me a call when you want to come get your new skid rig

Yeah Rob might give you a ring this arvo if i get a chance

I remember someone loosing a plugger last Easter, haha. ;)

It wasn't an organized cruise. I was out with Fritz and the biker boys. The harbour just started to get packed all of a sudden... Not as big as it used to be but there was still 40 odd cars there.

I've just realised there is the Touch up Guys right near my house... might go over and have a chat. Original owner of my V looked as though he attacked the rear Nissan badge with a screwdriver to get it off and left a very deep and large scratch on the back and i want it gone.

yeah man, you have to be very cautious where you take your car here. I've been burnt by 90% of the places I have taken my car to - Tuning shops, paint and panel, and engine builders.

There really isn't any better piece of mind than doing it yourself to be honest.

This is the main reason that I started tuning my car myself - because no one I asked or took it to had a clue. This was nearly 10 years ago.

Now I get called very often for tunes lol.

have you talked to Nur33 about his 350z turbo kit yet? lol

Good to know man, only problem with that is i've only just got into the mechanical side of cars so it's a massive learning curve. I've called 4 different places now just to get a bolt replaced in my front rear castor bar and aparently no one can do it. Such a joke.

Nah what happened to it?

Chris Pace in Furdsen Street Glenella does great work with panel and paint work. Got some work done on the 34 in there a while ago couldn't be happier.

+1

he did my old car and did a great job of it

Cheers, will take it in to him some time this week

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...