Jump to content
SAU Community

Recommended Posts

  • Replies 80
  • Created
  • Last Reply

Top Posters In This Topic

i can rock up at 10am, but i start work at 1:30, is it ok to just turn up for that amount of time? I work in south melbourne, so would be leaving about 1:20'ish...

any rough ideas at this stage when the awards will be awarded?

That is correct - only cars who are entering the Show N Shine will be permitted to park at Birrarung Mar.

Anyone coming along to have a look will need to find parking somewhere and walk in.

You will be able to join as a member on the day, but to make things quicker, I would fill in a membership form and bring it along with you, as well, with correct money.

So I can enter Mr Otto even tho he doesn't stand a chance of winning anything, just so I don't have to find alternate parking? :)

Entry to the pak opens at 10am, right? What's the time frame for Show n Shine entries since I doubt ferni will awake at 10am let alone be somewhere (other than a track) by 10am....

Can i join up us a vic club member on sunday if i bring the form and correct money?

I wont be entering in the show and shine, i just figured this will be easiest time for me to sign up as a member!

Can i join up us a vic club member on sunday if i bring the form and correct money?

I wont be entering in the show and shine, i just figured this will be easiest time for me to sign up as a member!

yes this is fine, a good time to join our fantastic club :)

:D

:P

Hoping to come down and meet everyone, sent membership application a week ago so hopefully I will be allowed in the gate :laugh: (I did PM Adzmax to check for me) :(

Anyone heading in from Eastern subs want to cruise in together? I am from Kilsyth.

Edited by Rflirty4

I should be there, but won't be entering. Too much competition in the R32 category.

Too bad we couldn't do a tie in with sexpo. Drive a skyline and get teh chicks! (or blokes if that's what you're after)

Guys this event is more about displaying the diversity of our club rather than a 'Autosalon' style car display.

The more cars we have tomorrow the better.

The trophies are just a bit of entra incentive so that the best car/s on the day get a little something.

If your car isnt in showroom condition, it doesnt matter, bring it along and put it on display so we can show the public what we have to offer.

See y'all tomorrow. :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...