Jump to content
SAU Community

Recommended Posts

still stuck shut.....do i have to remove the back seats or can i drill the lock out. Aim for the midddle of the lock and drill it out ?
Call a lockswith, to open the boot (ie: break in), then get them to make the boot lock work with your key.

:P

Easiest would be to just take off the back seats and open the panel. Then flick the switch.

I've done it before on another car.

I've taken the back seats in an r33 out in 10 minutes. Removing the panel took <5 minutes. Use a short pole to flick the lever and bob's your auntie. Then you can take it to the locksmith to have the lock repaired.

Imagine if you were standing outside your car and you have the lid open.

Right in the middle of the bottom section (on the inside), there is a little plastic flap. Inside there, there's a little switch. it's piss easy to flick.

No, you don't have to get in the boot. you won't be able to anyways.

like I said, i just used a pole to flick it (not on my car, my car's perfect and nothing ever goes wrong. was on my mate's r33).

cheers

ok I am with you...............I think u have open the plastic falp first yeah...?

So use a pool perhaps a flat screwdriver on the end of the pool taped to it?

I will try this tonight....effen boot.....Must be the Valet switch. never touch anything kids unless u know what it does....except females.

  • 2 years later...

i'm in a similar situation and i got no idea what to do...

my friend slammed the boot lid with god knows what on his mind, and now i can't open it using the lever near the drivers door or the key to open it from the actual boot! the key just turns, and comes to a stop in the position where the boot should be open, but the boot doesn't open. you can hear it un-latching off something, but im not sure if thats just the spring making a noise in the keyhole or the acutal lock. if it was that little switch that tripped then they key would over ride it (i'mm 99% sure im right on that bit). but the damn thing won't open even with the key!

any suggestions??

i'm in a similar situation and i got no idea what to do...

my friend slammed the boot lid with god knows what on his mind, and now i can't open it using the lever near the drivers door or the key to open it from the actual boot! the key just turns, and comes to a stop in the position where the boot should be open, but the boot doesn't open. you can hear it un-latching off something, but im not sure if thats just the spring making a noise in the keyhole or the acutal lock. if it was that little switch that tripped then they key would over ride it (i'mm 99% sure im right on that bit). but the damn thing won't open even with the key!

any suggestions??

fixed the problem! =) .. had 2 other people help. while one held the key in the unlocked position, me and the other friend pulled from both sides and it just popped open.. but took a bit of effort! wasn't easy.. working fine now so far.. lets hope no one slams it again =s

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...