Jump to content
SAU Community

Recommended Posts

Hi ppl,

I went from 2nd gear to 3rd gear, then tried to go to 4th but no go, the shift wont move in any direction. There is no grinding crunching or anything like that and the clutch is fine. has it grabed on the selectors? Anyone no the best way to free the gears?

cheers

Leigh

Edited by woolls
Link to comment
https://www.sau.com.au/forums/topic/149169-stuck-in-3rd-gear/
Share on other sites

  • 2 weeks later...

That's f**ked. I had my car stuck in 3rd for a while.. .it got gradually worse. Turned out to have sheared the round solid part that goes over the main axle(?) of the (SR) gearbox...

When it was stuck a few times I managed to unstick it a few times by playing with it.. i.e. not bashing but springing the pedal.. it's only going to work if it's lightly stuck. If it's well and truly gone nothing will shift it, I thought I'd bend/snap the shifter after 2 months of being desperate.

GL with it.

Well, I pulled the box apart, Found that a Part called shift insert had come out of the synchro hub. I think that came out because the shifting insert spring broke. The shift insert has done a bit of damage to the cluster, eveything else seems ok. Can get a brand new cluster for $700, A kit for $500 (main bearings seals gaskets, needle roller bearings and inner sleeves), new shift inserts $66 for 9, and the new spring inserts $6. About $1300 in total with me doing all the work.

cheers

Leigh

Edited by woolls

Thats what I like to hear...mine got stuck in 3rd...ended up costing me $900 all up including box out/in/oil, machining flywheel and fitting new clutch...so I guess I got it at an alright price....I won't mention that it took almost 3 months to be fixed though.....

Strange coincidence...mines a 98 model as well

Thats what I like to hear...mine got stuck in 3rd...ended up costing me $900 all up including box out/in/oil, machining flywheel and fitting new clutch...so I guess I got it at an alright price....I won't mention that it took almost 3 months to be fixed though.....

Strange coincidence...mines a 98 model as well

Might of got out of it cheaper if I didn't drive about 20 clicks with it stuck.

I have been told that nissan made some changes to the box from the mid/97 to the 5/98. Mine is the 3/98 and falls into this. if it was the 5/98 or later a cluster would of cost me $440. Such as life.

Edited by woolls
Might of got out of it cheaper if I didn't drive about 20 clicks with it stuck.

I have been told that nissan made some changes to the box from the mid/97 to the 5/98. Mine is the 3/98 and falls into this. if it was the 5/98 or later a cluster would of cost me $440. Such as life.

Appaerently mine has some R34 internals...thats what I was told anyway, but that may have been excuses from the workshop seeing as how it took them almost 3 months to figure out what parts they needed :D

Appaerently mine has some R34 internals...thats what I was told anyway, but that may have been excuses from the workshop seeing as how it took them almost 3 months to figure out what parts they needed :glare:

From what I've found out , if your car has a build date of 5/98 or > its got what they call the series 3 box. Thats what I have been told anyway.

Yeah, dezz we'd have the same gearbox.. i've still got my main bearing stuffed and it's whining.. probably look at getting it fixed sometime..

Late R33 gearboxes are probably worth fixing rather than replacing..

Woolls, you have much trouble getting it out and pulling it apart?? Got any photo's.. def interested..

Late R33 gearboxes are probably worth fixing rather than replacing..

Woolls, you have much trouble getting it out and pulling it apart?? Got any photo's.. def interested..

Have replaced the box with a brand new one, but I will be gathering the parts over a period of time to rebuild my old box.

They are not to hard to pull apart, (you will need a couple of gear pullers) Its just got to be pulled apart in the right stages, no bloody short cuts.

Sorry I took no pics, but when I go to rebuild it, I will take some pics and do a write up on it. (won't be for a while)

Edited by woolls
Tidy, mind if I ask what that set you back?

$3150 delivered to tassie, Retail at nissan was 4900, I could of got one off them for 4100. Just Jap sells them for 3200. But just jap and Nissan have none in Australia. I end up getting this one through a member on SAU.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...