Jump to content
SAU Community

Recommended Posts

http://www.pickles.com.au/servlet/Auction/...em_id=252053789

Was looking at getting this car and repairing it.

Do you guys think it would be worth it?

I'm looking to get a cheap car, and i was thinking that i could get a newer car that was damaged and i could repair it, thus making it cheaper than if i was to buy it in good condition.

If you think it's worth buying and repairing, what do you think would be a reasonable purchase price??

And what would be you guys estimate on repairs?? (also read the damage details on the site to give you a better idea)

Cheers

Link to comment
https://www.sau.com.au/forums/topic/150947-opinions-on-this-wreck/
Share on other sites

If you got the wreck FOR FREE it still wouldn't come close to a "cheap" repair bill.

I've worked in damaged-auction yards in the past & as soon as you see Heavy Structural in the damage listings it's usually only viable if you own a shop with all the equipment & can do it all yourself. To pay to have the work done would be prohibitive- remember it was written-off in the first place for a reason.

I've even processed vehicles that had VERY minimal panel damage that were financial write-offs purely based on the cost of replacing the air-bags etc. Worth a look maybe, but I'm guessing it would only end in tears.....

This car is good for parts only i reckon. I wonder how much it would go for. i could use alot out of it to sti spec mine lol. when it going on auction i cant find the auction time anywhere

Dont worry found it 16/01/07

How about import one from Japan and use this one registration plate?

NO that's illegal mr west.

plus you'll not get one into the country without a CAMS L3

on a side note, see all those nice pink arrows? a repairer has gone over it and marked where the body has moved... looks like the whole shell is twisted in the direction of the arrows

NO that's illegal mr west.

plus you'll not get one into the country without a CAMS L3

on a side note, see all those nice pink arrows? a repairer has gone over it and marked where the body has moved... looks like the whole shell is twisted in the direction of the arrows

Holy shit. My bad.

Only coz i see lots of EVOIII registered them self as Lancers then Engineer to be Evo's.

There's no info on whether it's a repairable write-off or a statutory write-off.

Before you even think about buying it, find out which it is.

I don't think you'd be too happy if you purchased a car to repair, then found out that you've just purchased a statutory write-off.

i think it will only be good for parts. u could always upgrade a normal RS to sti spec with parts from this. as far as wests swap, i think every state has different laws but most now will not let similar happen and have changed or brought new laws in to stop things like that. but i think it could still happen but lets hope u dont get caught driving a car like that or sell it

well the car is a repairable write off, it says that in the catalogue before you enter that page.

I know that it would not be worth repairing, but does anyone have any idea of the price for repairs?

Im guessing 10k+

well the car is a repairable write off, it says that in the catalogue before you enter that page.

um...

from the index page:

CP 09/05, SUBARU, IMPREZA, S MY05 WRX STi, Sedan, 5 Seats

MANUAL, 2.0 ltr, 4 cyl, Premium ULP, Multi-Point Injected Turbo intercooled, 0 kms (Showing On Odometer), BLACK, Rego.No:NP(TTC115), Aircond., Airbag Dual, P/Steer, P/Wind, IRS, Cru. Cont, Cent.Lock, CD Stacker, CD Player, Radio, Immobiliser (App), Body Kit, Double Glazed, DVD, Rear Spoiler, Turbo, custom wheels (Stock No. 3131897), GST Included in Sale Price

I don't see anything there about whether it's repairable or not.

i think it will only be good for parts. u could always upgrade a normal RS to sti spec with parts from this. as far as wests swap, i think every state has different laws but most now will not let similar happen and have changed or brought new laws in to stop things like that. but i think it could still happen but lets hope u dont get caught driving a car like that or sell it

damn right it does happen...

it's called stolen cars and rebirths!

step 1. acquire 'repairable right-off' or statutory right off

step 2. acquire* perfect vehicle that is the same, but not banana'd

step 3. remove and swap plates

step 4. present to relevant government registration body for re-registration

step 5. sell for mucho cashola

*may be acquired by non-legal means

thankfully data-dot technology is starting to make this more difficult; stolen cars tend to end up in parts rather than rebirthed. If only they sold data dot paint to general consumers so i could unleash it all over my car!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...