Jump to content
SAU Community

Recommended Posts

Okay guys. I have been searching and searching and have been unable to find what I am looking for.

Esentially what I want is a two step launch controller for my GTR33. I want the type that allows boost to be built at a standstill so that you come off the line with full boost.

I know that the Power FC pro has a type of launch controller, however I dont believe it does what I am looking for. That plus the fact the discontinued the FC Pro. I also know that Bee-R has a rev limiter, however I believe that ALSO does not allow you to build boost on the line.

So, if someone could recommend one to me it would be GREATLY appreciated. Thanks.

-Sayajin

Link to comment
https://www.sau.com.au/forums/topic/153794-two-step-launch-for-gtr33/
Share on other sites

anything with a zero speed ignition cut should allow you to build boost. I know it works on my emanage ultimate

Such as what unit? Reason I ask is I am currently on the Power FC so I cant get a new stand alone just for launch control.

-Sayajin

Humm... this is a bit different from what I had heard before..

So I can set the rev limit to 6500RPM, stand full on the gas and it stays at the set RPM, and builds full boost while still on the line?

-Sayajin

yep got it in one. you have 2 rev limits one is a stationary (launch) rev limit that usualy is engaged either when speed = 0 or when handbrake is engaged. once speed is above 0 or handbrake is dropped it reverts to the usual rev limit. so you can set limit one to 6500rpm if you wish for launch, then limit 2 to 8000rpm for driving. as for whether it will build full boost I'm not so sure of that. it will build some boost though.

Okay guys. I have been searching and searching and have been unable to find what I am looking for.

Esentially what I want is a two step launch controller for my GTR33. I want the type that allows boost to be built at a standstill so that you come off the line with full boost.

I know that the Power FC pro has a type of launch controller, however I dont believe it does what I am looking for. That plus the fact the discontinued the FC Pro. I also know that Bee-R has a rev limiter, however I believe that ALSO does not allow you to build boost on the line.

So, if someone could recommend one to me it would be GREATLY appreciated. Thanks.

-Sayajin

It's hard to go past the MSD 2 step...

Ever used the Gizmo Paul? Now that you mention it I remember reading about it QUITE a while ago. I only ever heard of one person using it however so I am unsure on how well it works.

Any first hand experience?

*edit*

After reading the Apexi page all I can say is WOW.... Sounds like exactly what I want. Hell it even has flat shifting! (no lift to shift).

Also I read that it integrates with the shift light. Does that mean in order to get the Gizmo to work I need the shift light as well? Or just means it CAN work with it?

-Sayajin

Edited by Sayajin

no sorry, never used it. when i get an evo i will get one for sure

i see no use it for in my skyline (rear wheel drive & stock ceramic exhaust wheel)

from memory youll need or want;

stand alone ecu or good remap

steel wheel exhaust wheel

no cat

exhaust temp gauge might be a good idea

good traction

yeah its a nice device hey

yeah the shift light is optional that i can see

on the evo forums theres a video of one dude that has a 2 step spark cut limiter. the video shows the car stationary with 1.3 bar ready to go and lotsa flames out the exhaust

Humm.. well I have been reading around and it appears that the shift light is REQUIRED in order for the launch interface to work.

The Tach recall intercepts the RPM line from the ECU. This allows you to control your 2 shift points, warning and shift now - and also the launch.

A 5V signal is sent from the tach recall light to the launch control interface when the desired rev point for launch is reached.

Still seems like a great thing. I just personally feel the shift light is a bit too ricey for myself. I may have to make an exception however. That or just remove the bulb in the light. lol.

Or if someone else has something better that is just as well!

Thanks for the info Paul.

-Sayajin

Edited by Sayajin

Something you may want to think about is how is it actually limiting the rpm....

Yes some of the ECUs may have an option to hard / soft cut - fuel / spark but the million dollar question is how crudely they apply that limit.

My Haltech has these features too but I am planning to rely on the 2 step functionality built into my MSD DIS4

The reason I recommended the MSD is because the MSD alternates the cylinders it drops and some cheaper rev limiters may only drop the same cylinder causing fuel build up in that cylinder. Just make sure the ECU you plan to use alternates the cylinders.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...