Jump to content
SAU Community

R33 Rb30 Conversion

JNR24

By JNR24,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 7.2k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Duncan
Duncan

Just thought I would bump this 20 year old thread because the Skid Factory have just posted up a video summarising a lot of the content, format might be more familiar for newer members

JNR24
JNR24

fyi guys, Well yesturday i picked up a RB30 for my conversion into my R33. I will be using my RB25DET head on the RB30 block. So i started stripping the motor down, pulled the crank, pistons, girdle

Cubes
Cubes

Here is all I have at the moment: http://www.geocities.com/r32_jjc/ Unless you are on broad band make sure you right click then save as. The file is around 120kb. If there is anything I have got w

Posted Images

Alf Proficient

Alf

Posted
Posted (edited)

Every head should be CC'd if you dont knows it's history.

I know mine had the face machined prior to me buying it and again was faced after the front water gallery was tigged up.

My R33 RB25DET head's bowls averaged at 58.7 CCs . It's time consuming to get the bowls volume close to each other (0.2CC +/-). :)

no. 6 cyl had the largest bowl volume: 59.8CCs. Had to remove a bit of material to clean up the pitting left from detonation.

PS: I used a burette to measure the bowls.

Edited by Alf
GTRgeoff Grand Master

GTRgeoff

Posted
Posted
Problem solved.

Looks like the cat or middle muffler has collapsed and blocked most of the exhaust.

Got it to 1 bar after I dropped the exhaust at the dump pipe flange and went for a blat up the street.

Whoo hoo, now to just replace the cat or muffler and back to the dyno.

Think Ill have a few beers tonight.

Hope those beers were good.

I should have thought of that. I had a cat collapse once and it was doing similar, but seems fairly uncommon. Well done.

Adriano Grand Master

Adriano

Posted
Posted

the greddy copy manifolds have been discussed in the froced inuction forum, the casting quality seems to be poor, and you can get them off ebay for about $200, noone has got dyno proof yet if they work. I think the siemens injectors are all top feed, so unless you get an r34 fuel rail, which fits the greddy copy manifold, they wont fit. Even with the rail, im not sure if the siemens are the same dimensions as the r34 gtt injectors

Roy Grand Master

Roy

Posted
Posted
Ohhh ok.

I just thought they had smaller housings than a GT35 or are they the same but with smaller wheels?

Do a search for the results of R31Nismoid...its his old turbo that you are talking about.

Also, another quetion... those of you running RB25 heads vs Rb26. IS there a measurable difference between the results are ppl getting with the same turbos...main variable being head and inlet plenum?

Not sure if i should bother with an RB26 head or not

Sydneykid Grand Master

Sydneykid

Posted
Posted
Do a search for the results of R31Nismoid...its his old turbo that you are talking about.

Also, another quetion... those of you running RB25 heads vs Rb26. IS there a measurable difference between the results are ppl getting with the same turbos...main variable being head and inlet plenum?

Not sure if i should bother with an RB26 head or not

Forget about whether or not the RB26 head itself is "better", the fact is it will work out cheaper when you add it all up. Inlet manifold, multiple throttle bodies, plenum, top feed injectors, cams, solid followers, no VVT, adj camshaft pulleys, valves, valves springs etc etc. They are what makes an RB26 head the ONLY way to go.

:P cheers ;)

Spoolup Mentor

Spoolup

Posted
Posted

I cut the cat out of my exhaust today - it is completely screwed and deformed internally. If you hold it up to the light you can not see any daylight.

In the end I couldnt even get the car to idle there was that much back pressure.

It is approx 2500 kms old - I am currently in discussions with regards to a warranty claim so dont want to mention any names as yet. It was not a cheap item though.

Spoolup Mentor

Spoolup

Posted
Posted

yeah - that gets a little expensive when you get defected and they decide to take a closer look - I did consider it though.

Custom Exhaust Specialists in Bris are doing me a 3.5 inch custom cat they have XR6 turbos making 700-750 flywheel horsepower with - its cheaper than the 10k fine :-)

time to put a "hi flow" one in then? :P
Guilt-Toy Grand Master

Guilt-Toy

Posted
Posted

i need to scan it this weekend but i ran outta fuel so i need to do more work on the dyno after i change the pump.

How is a good way to get out of the fuel problem? i want to get over 400rwkw if i can with the stock head.

peek power was at around 160ks an hour in 4th gear.. i need to bring it down a bit but wont worry about that untill i get the fuel pump situation fixed up.

Full Boost comes on - 110ks an hour (20psi) in 4th gear all the way up to the end 20psi

It even has 5psi of boost at 92ks an hour in 4th.. comes on early i wreckon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Stagea Front CV Axle Question

      By soviet_merlin · Posted

      Man, different parts but the same numbers is terrible @dbm7! And it doesn't help that most online shops don't list the part numbers at all. They just give a list of compatible models...
    • MBS206
      R32 GTST - 600KW+ RB28/CD009 Build

      By MBS206 · Posted

      Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • dbm7
      Stagea Front CV Axle Question

      By dbm7 · Posted

      Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • Duncan
      Stagea Front CV Axle Question

      By Duncan · Posted

      I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • soviet_merlin
      Stagea Front CV Axle Question

      By soviet_merlin · Posted

      One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
×
×
  • Create New...