Jump to content
SAU Community

Recommended Posts

  • Replies 96
  • Created
  • Last Reply

Top Posters In This Topic

new i think they are about Y27000 a piece for 18's just FYI...

yeah S13 sorry did i put S14? the rack its self is about the same but the actual steering shaft is for sure a S13 two piece instead of a S14 solid shaft....

Edited by 4DoorWhore

dammit now your mixing me up... haha yeah teh come factory s13 rack, i have R32 tierods, and its on a S13 engine member instead of the A31... wait im lost? what are you asking?

dammit now your mixing me up... haha yeah teh come factory s13 rack, i have R32 tierods, and its on a S13 engine member instead of the A31... wait im lost? what are you asking?

lol now i'm getting lost

S13 engine mount and rack with 8mm rack spacers equal ridiculous angle...

da 8mm rack spacers was da only thing dat gave u more steering lock('angle' as u put it) yea?

wooo hooo it runs, well sort of......... starts up like a champ... doesnt quite idle so i need to do some fine tuning but i had to take some pics for so people so ill go ahead and post what i got so far....

once i get it running solid and make the brackets for the IC and rad then ill take it down to a friends shop to get th IC piping made...

Major hard-parking cause like i said it doesnt run quite right yet... and all the panel and aero are just ziptied on... and it NEEDS TO BE LOWERED, and a different set of tires... haha its at that Ozzy ride height and needs to be at that Japan height (no offense)

first the pretty pics...

DSC02180.jpg

DSC02184.jpg

DSC02187.jpg

DSC02190.jpg

DSC02185.jpg

pics taken by a friend -yokotas13-

IMG_4309.jpg

IMG_4308.jpg

IMG_4307.jpg

IMG_4306.jpg

IMG_4305.jpg

heres where I need help... like i said it runs but doesnt idle, im not saying these are the problem but id like to get these pluged into the right places... so if these look familiar and you know where they go chime in...

this is a factory 92 MT Kouki RB20E cefiro with a Kouki S14 SR engine/ecu harness, im pretty sure the old owner of the swap had it in a Zenki factory AT RB20? Cefiro

DSC02193.jpg

from the MAF area...

DSC02197.jpg

other side these are from the fuse box...

DSC02198.jpg

DSC02199.jpg

thanks for all the help and good words....

Edited by 4DoorWhore

no fkn wounder it doesn'r run rite.. its got no cooler

pls tell me wen u were running it da rad was connected and filled? :D

oh nd yea grants fotos are always great :(

Edited by Dan_J

we used to have a '15 year' import rule - where compliance was consideraly less. so a couple years ago 1990 and 1989 cars were brought into aus really cheap! That rule has now changed, but we can still bring in 88 and pre-88 cars cheap.

Bugger - as yours is a 92, i think it 'might' be able to be brought over to aus, but wouldnt be worth it (as a 88 ceff compliance would be $1000 or less and your 92 one would be roughly $4000 Aus dollars)

i bought my ceffy a couple years ago for $7000 australian dollars, which at the time was pretty cheap. it was a bit rough, but it had a couple of nice things on it, and now its come a Long way - with more goodies next week :) Muhahaha

Bugger - as yours is a 92, i think it 'might' be able to be brought over to aus, but wouldnt be worth it (as a 88 ceff compliance would be $1000 or less and your 92 one would be roughly $4000 Aus dollars)

daaaaaaaaaamn!!! thats crazy... :laugh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...