Jump to content
SAU Community

Recommended Posts

it may not be factory, but i have seen one before on an R32 m spec. it was making 210rwkw. also came with the electric spoiler.

I thought it was factory.

the one i saw was exactly like the one listed but also had a shroud. it is not a backyard job. look at the end tanks and mounting hole.

Still looks the goods to me

overall heat transfer coefficient for a wall can be calculated as:

1 / U A = 1 / h1 A1 + dxw / k A + 1 / h2 A2 (1)

U = the overall heat transfer coefficient (W/m2K)

A = the contact area for each fluid side (m2)

k = the thermal conductivity of the material (W/mK)

h = the individual convection heat transfer coefficient for each fluid (W/m2K)

dxw = the wall thickness (m)

Aluminium Coefficiant: - 221 W/mK

When aluminium is used as a heat exchanger in ambient air medium

U = 1 / (1 / hA + dxw / k + 1 / hB) (1b)

Taking the total medium transfer to: U = 25.0 W/m2K

even if the air temp in the cores is 70deg C the total increase of air temp traveling thru the second core from the first will be nothing compared to the temp coefficant.

in other words....

it will perform very well.

Well the ARC type are 110mm thick. This is 130mm (2 x 65mm) . The air flows through the fins from frotn to back - shouldn't be a real issue.

It won't be quite as good in cooling as a taller skinnier cooler but it should flow ok.

Might connect up a water spray for hot days...

Way I see it if it can handle 220rwkw I'm laughing.

Benfits:

1. easier to fit

2. looks stock

3. wont lose response like with a FMIC

3. good for insurance etc.

downside:

1.not as good cooling

hmm well i had a r34smic, then upgraded to a fmic (r34 is exactly 61% bigger in core size btw) but maybe i'm not seeing things correctly but that piping (entry and exit points) doesn't really look like it will bolt up correctly to the stock 33 piping?

Maybe its a r32 one? as i recall they have a different piping setup to the 33/34

I put a 34 SMIC in my car, and it pushes right up against the front bar. This thing looks like it would want to sit much further forward?

The distance from the inlet/outlet to the back of the core looks the same as my 33 and 34 cooler, so the extra thickness APPEARS to take more space at the front?

Definitely keep us updated on the flow results! I'm keen to know how much better this 34 cooler is over the 33 one, regardless of the dual-core setup.

I put a 34 SMIC in my car, and it pushes right up against the front bar. This thing looks like it would want to sit much further forward?

The distance from the inlet/outlet to the back of the core looks the same as my 33 and 34 cooler, so the extra thickness APPEARS to take more space at the front?

Definitely keep us updated on the flow results! I'm keen to know how much better this 34 cooler is over the 33 one, regardless of the dual-core setup.

cant comment on the stock bar as i've always had a aftermarket one (as pictured in my av) but i did measure back to back the cores (stock 33 vs 34) and from memory the 34 core is a couple of cm taller (so sits lower) and 2cm thicker, but no wider,so would sit a tad forward yes

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...