Jump to content
SAU Community

Recommended Posts

Yes that is a pig of a hose.

you will need a long set of needle nose pliers to get the clamp off and then spray a tiny squirt of wd40 inside and outside the hose and twist. it will come off.

getting it back on is another story...

yeah, there's no easy way out. You need tiny hands. Try and undo the clamp anyway you can.

Either a long screw driver if you can, or needle nose pliers.

I cut an 8 mm spanner in half and got my hand in (I lubed it up with soap and got it in - yes i was scared i'd never get it back out)

once you get the clamp undone enough, you can get the line out, by pulling the line itself from outside

If you're installing the hks turbo and replacing the line with a braided one, I have no idea how on earth you'll get the new line in.

The water line that runs around the back of the head is bolted to the head with a 10mm head bolt the same as the ones holding your fenders to the chassis.

Remove the heater hoses and push them up to gain access to it.

There is only one and its in the center of the head.

You can also access it by removing the valleycover and pushing the wire out of the way.

Remove the bonnet also it makes it much easier to see.

Why would you want to remove it though?

You can just cut the other water line pipe (return from the turbo) and join them with some high temp hose.

:)

Been there, done that. Not fun.

Having 2 people to remove it helps, one holds the hose and the other yanks on the metal line.

For install of braided lines atleast you can bend the rubber hose up and fit the barbed end of the braided line, then feed the other end of the line back around the back of the head.

The water line that runs around the back of the head is bolted to the head with a 10mm head bolt the same as the ones holding your fenders to the chassis.

Remove the heater hoses and push them up to gain access to it.

There is only one and its in the center of the head.

You can also access it by removing the valleycover and pushing the wire out of the way.

Remove the bonnet also it makes it much easier to see.

Why would you want to remove it though?

You can just cut the other water line pipe (return from the turbo) and join them with some high temp hose.

:)

Just hacksaw the metal pipe off, probably as close to the turbo as possible????

I guess I'm worried about metal filing getting in there and also, there would be no lip to stop the pipe coming off..(or would that not be a problem ? )

Have a go ya mug!!!

Actually to tell the truth, mine was held on with the hose clamps that you pinch together with a set of long handled pointy pliers [$10 at Crazy Joes or Micks or somesuch]. The hose was a bit stuck, so I used a long thin screwdriver to work under between the hose and the metal pipe and some WD40 and it came out easy. Don't ask me how to put it back on, I haven't got that far yet..........lol.

PS I don't have a valley cover. that probably made it easier. Actually I found the bolts that screw into the block that hold the stays on this hose harder to get off than the hose.

metal filings are not really an issue wiht that particular hose. That is just a coolant hose, so ti's just the cooling system - just water.

Ther'ell be plentny of shit in there anyways, like everytime I dropped the coolant in my daily driver (not my skyline), there's all rust, and crap that comes out.

Don't get metal in the oil lines though. Totally different story

It's not that easy mike, coz jase is getting the line replaced as part of the turbo install.

Also, I'd replace that rubber hose at the back. Someone recently, forgot who it was had the hose blow (they're' 10 years old afterall). Better do it now while the turbo is off. Imagine if it blows in 6 months time and having to do it with the turbo on!

If you cut the line, keep in mind that the cooling system is under pressure (up to 0.8bar). Without a bead around the line, the hose can possibly blow off. Imagine having the line blow off on a hot day as you're driving along the freeway. bye bye engine

I've just cut mine, about 30mm before it bends around behind the head. I went to pirtek and bought a compression gland to adapt some braided stainless teflon hose on. works great and looks good, and heat isn't an issue.

If ya want photos I can get some.

It's not that easy mike, coz jase is getting the line replaced as part of the turbo install.

that is wat i did when i replace my turbo with a HKS turbo. and the hks turbo came with a braided line. so i cut it just before the bent.

basicly the same as "Ol_Mate" did!

undo the bolt behind the head, then un hook that entire line from the back of the plenum... and yes replace that section onto the plenum, mine let go after my turbo upgrade, wasnt easy to get to with it all bolted back up.

you could just remove the solid line all together and run the braid from the back of the plenum

I've just cut mine, about 30mm before it bends around behind the head. I went to pirtek and bought a compression gland to adapt some braided stainless teflon hose on. works great and looks good, and heat isn't an issue.

If ya want photos I can get some.

Photos would be great !

So you didn;t need a lip on the end of the pipe with that gland thing?

undo the bolt behind the head, then un hook that entire line from the back of the plenum... and yes replace that section onto the plenum, mine let go after my turbo upgrade, wasnt easy to get to with it all bolted back up.

you could just remove the solid line all together and run the braid from the back of the plenum

Exactly what I did, you dont wanna be ripping that son of a ***** off more than once in your lifetime :( My knuckles have never been the same since :happy: /emo.

Exactly what I did, you dont wanna be ripping that son of a ***** off more than once in your lifetime :( My knuckles have never been the same since :happy: /emo.

Do it right, do it once :happy:

You can do it. Motivational thread for jase. go jase go jase go jase :)

Edited by MANWHORE

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...