Jump to content
SAU Community

I Can Wobble My Rear Wheels With My Hands

Birth
 Share

Recommended Posts

Birth Experienced

Birth

Posted
Posted

Hi all, I would like some advice.

I have jacked my car up off the ground and found that I can wobble my rear wheel about 5mm by applying fairly slight pressure with my hands on the left and right hand side of the wheel. It does not wobble when I shake it from the top and bottom. Is this normal? Have I got worn bushes? Tyre wear seems normal.

My car is a 1993 R32 GTS4 with stock arms / bushes, GTRGeoff hicas lock bar and whiteline shocks.

I have put a (dodgy) pic of what I mean to help with my explaination.

Thanks,

Ben.

post-28712-1172791431.jpg

WogsRus Veteran

WogsRus

Posted
Posted

sounds like a worn bussh somehere. Go to pedders and get a $14 28 point safety check, that is the best way to pick up problems. After that you can do all the work yourself.

There are a few bushes there, so maybe take the wheel off and have a good look arround. Maybe a ball joint on the lock out bar.

BHDave Grand Master

BHDave

Posted
Posted

combination of old soft rubber bushes front and a flogged out tierod ball joint (or tierod end) rear.

If you remove the rubber boot on the end of the hicas rack and get someone to move the wheel for you it's pretty obvious if the ball joint is shagged. Any movement = borked

gts4diehard Rising Star

gts4diehard

Posted
Posted

it will be combination of the link bushes and the tierods, more likely the tierods. Did you fit the old steering arms to the hicas lock bar?

The rear bushes needs a little movement in them because the hicas is basically compressing the bushes to give the car rear steering.

But you should not feel any movement at all by hand.

First thing I would try is new steering arms (from the hicas lock bar to the tierod end in the hub) as the ball joint might be worn. If that doesn't cure it then you will need to remove the hubs to replace the link bushes in the hubs. Once you see how involved that is you might as well replace the lot, because its not a job you want to do twice!

I replaced the bushes in my hubs, and the steering arms and that tightened up the rear end so that you couldn't feel any movement at all. The next step would have been to replace the bushes in the links themselves to have basically new rear suspension.

The car felt more controlled at high speed into corners after that (on qld raceway), and I think that the Hicas was not in any way detrimental to the cars handling considering that the hicas was now working with components in good condition.

  • 10 months later...
noone Experienced

noone

Posted
Posted

When removing the rear hub assembly did you have to replace many parts

was wondering if i can just unbolt the shafts and the hub assemblys etc

replace tierod /hicas ends in a press then bolt it all back up?

I assume you would have to use a press or maybe a porta power to actually press the tierod /hicas ens out of the hub assembly etc

  • 5 months later...
RB20JT Rising Star

RB20JT

Posted
Posted

sorry mate what are s/h items...my car has done 125000kms...but the guy before me had shopped springs in it..so that would have sped up the wearing out process...

also what do they cost and from where?

Cubes Grand Master

Cubes

Posted
Posted
sorry mate what are s/h items...my car has done 125000kms...but the guy before me had shopped springs in it..so that would have sped up the wearing out process...

also what do they cost and from where?

s/h = second hand.

chopped springs would be unlike to cause damage. Hitting gutters ripple strips etc would. :)

I picked up a complete rack from Wally at Zimports for bugger all can't remember the price but it was under $100.

I recently bought a new steer rack with rod ends as the front left did the same; that cost me $100 for the complete rack and tie rods.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Duncan
      What brakes on R34 GTT(Europe)

      By Duncan · Posted

      Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...