Jump to content
SAU Community

Trust Greddy Plenum On R34

ovabooster

By ovabooster,
in Engines & Forced Induction

 Share

Recommended Posts

Stronzo Collaborator

Stronzo

Posted
Posted

hi,

Since it was designed for r33 (not neo) and since neo head has slightly different intake ports and AAC valve bolt pattern -- sure it will require more work to install it to neo engine.

But there is nothing impossible.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
I love how everyone who has it fitted wont explain what was necessary to make it fit. This is a forum where people share information, so share, please.

Agreed.

Its the same people saying it "can" be done, or they "have" done it. But wont go as far to to share how it was done

STATUS Grand Master

STATUS

Posted
Posted (edited)

OK it is bolt on;

just use a set of fuel rail spacers or R33 GTS-t rail kit, a R33 throttle body and greddy adapter or even better use an infinity item like in my pics. Very simple :dry: no black magic :P just a bit of re-looming to keep it all factory neat.

post-34927-1174340883.jpg

post-34927-1174340904.jpg

post-34927-1174340920.jpg

Edited by URAS
satanic Grand Master

satanic

Posted
Posted

Standard R34NEO injectors I see... that's weird; general concensus a while back was that R33GTST injectors would be needed (top v side feed)

This is interesting; has dispelled a LOT of myths.

My question is this though; you say to use a R33 TB or other one... won't this remove a few components of the R34 since the NEO TB has a massive donk out the front which controls a few things?

Interesting work; well done!

Sydneykid Grand Master

Sydneykid

Posted
Posted
OK it is bolt on;

just use a set of fuel rail spacers or GTR rail kit, a R33 throttle body and greddy adapter or even better use an infinity item like in my pics. Very simple :D no black magic :P just a bit of re-looming to keep it all factory neat.

Very interesting, some questions;

What o’rings/spacers/adaptors are used to fit the R34GTT (top feed) injectors to the R33GTST (side feed) manifold?

Why can’t you use the R34GTT throttle body? The throttle butterfly is the same ID, is it the bolt spacing that’s different? Possible to use/make an adaptor?

What throttle cable is used?

:dry: cheers :huh:

  • 7 months later...
SCR34M3R Rising Star

SCR34M3R

Posted
Posted

i know its a old post

but trying to do this atm, i got some R33 Fuel rail spacers, but it doesnt seem a tight fit as it should be? did you use anything else? or there something you can do to make it tight?

also need a R33 ACC valve, as 34 one is bigger

Cheers

Justin

STATUS Grand Master

STATUS

Posted
Posted
forgot to mention you lose traction control (a given since the TB controls it).... i hate it anyway :D

finished one with trac control still working for those that want to keep it.... piping is a nightmare though.

STATUS Grand Master

STATUS

Posted
Posted
i know its a old post

but trying to do this atm, i got some R33 Fuel rail spacers, but it doesnt seem a tight fit as it should be? did you use anything else? or there something you can do to make it tight?

also need a R33 ACC valve, as 34 one is bigger

Cheers

Justin

in rail or in the manifold?

SCR34M3R Rising Star

SCR34M3R

Posted
Posted

in manifold, fuel rail is all good, real tight fit. But put the 33 spacers in the manifold and then injectors into the spacers and isnt tight at all unless only pushed in a little bit and its sort of tight, but not like pushing into the stock manifold.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...