Jump to content
SAU Community

Greddy Intake Plenum (manifold)

subie

By subie,
in Engines & Forced Induction

 Share

Recommended Posts

STATUS Grand Master

STATUS

Posted
Posted
Hi peeps,

Does anyone know where can I get this type of Manifold ? (to suit RB20)

manifold-1.jpg

Cheers

Ford

thats a greddy flop to suit RB25, i hope they have fixed the coolant passage water injection from those copies now :D i have seen at least 5 hydro'd engines from them now.

but seriously hypertune and so forth do fabricated plenums for rb20 from memory.

STATUS Grand Master

STATUS

Posted
Posted
Ebay Link 1 is what I have on the way. Best design I have found thus far. Uras, didnt Trust make an RB20 one yeons ago???

nah cause twentys are gay :D

haha kidding. is yours making noise yet? when we going for a test drive.

Wheezy Mentor

Wheezy

Posted
Posted
nah cause twentys are gay :laugh:

haha kidding. is yours making noise yet? when we going for a test drive.

HRMMM strange, I vaguely remember seeing a picture of one on the R31 House site a while back (translation wasnt too good, but ah well)

Mine goes broom broom just after easter (I HOPE), Ill have to give u a ride, personally Im scared :rant:

teazn_r33 Mentor

teazn_r33

Posted
Posted
thats a greddy flop to suit RB25, i hope they have fixed the coolant passage water injection from those copies now :laugh: i have seen at least 5 hydro'd engines from them now.

but seriously hypertune and so forth do fabricated plenums for rb20 from memory.

i have one of these wat you mean buy that wanna make sure before i put it on

STATUS Grand Master

STATUS

Posted
Posted (edited)
i have one of these wat you mean buy that wanna make sure before i put it on

im based in melbourne and got called out to a workshop (remain unamed) to investigate genuine greddy plenums (turned out to be copies) hydraulic locking engines...... it turned out that a whole batch of these copies landed in melbourne and the manufacturer had tapped thru the water passage into the intake runner.... nice work. just pressure test the water passge if your worried.

Edited by URAS
Halo a Community Regular

Halo a

Posted
Posted
Unless its a pretty wild RB20 then dont bother. The std plenum seems to work really well for the sort of power you are going to get out of a 2L 6 cylinder. Spend all you rmoney on good quality bits, mainly turbo and a good tuner and you will get good results

+1

  • 2 weeks later...
Wheezy Mentor

Wheezy

Posted
Posted (edited)

plenum.jpg

Got this today....Its a KU Engineering one....Friggin top notch welding and design....Im stoaked...Should go nicley.

EDIT: Its really shiny too just my camera sucks the fat wang! (not that shine does anything for its performance) Also its fairly thick - the chamber, not just my old fella :happy: so it shant have problems leaning out a rear cylinder. But time will tell..

Edited by Wheezy
AD4M Proficient

AD4M

Posted
Posted
Unless its a pretty wild RB20 then dont bother. The std plenum seems to work really well for the sort of power you are going to get out of a 2L 6 cylinder. Spend all you rmoney on good quality bits, mainly turbo and a good tuner and you will get good results

couldnt agree more with Roy, i make 366.3hp (on two diferent dynos one in shootout mode) and still have more room to play, only real benifit you'll get is shorter pipe work.. spend the money elsewhere

Wheezy Mentor

Wheezy

Posted
Posted (edited)

HEHE Luckliy the figures that I'm chasing are higher. I totally agree that on pretty much any RB20 its not necessary, but it does get rid of alotta pipes and hoo ha when you wanna get to something on the engine :happy:

OH, and if youve spent the money everywhere else and am stubborn like me and wanna stay RB20 then go for eeeeeettttt

Edited by Wheezy
Roy Grand Master

Roy

Posted
Posted

What power are you chasing from the RB20? It will be interesting to see what power it makes with the plenum. Be great if someone could do a before and after with the plenum...i would except i just experimented with my engine at some expense only to put it back to the way it was so im shy about trialling anything for the time being

legend01 Experienced

legend01

Posted
Posted

I'll want to do the b4 and after thing with my rb20 after its all run in and going properly with the plazma man plenum just to see if there are any gains,but thats a while off just yet

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Gantai
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By Gantai · Posted

      Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...