Jump to content
SAU Community

Recommended Posts

Hi,

i want put a bigger turbo or hi flow the stock one? Which is better as i dont wanna change internals but want my engine not to blow or fry a piston. What is the best turbo for minimal lag, most power and a good amount of power at the wheels with standard RB25DET.

thanks

JOHN

If you're after response and good average power across the rev range, then I'd recommend a highflow - good bang for buck and should easily see 220-250rwkw with the right supporting mods.

If you have enough coin and are after more power whilst still maintaining decent response, then the HKS GT2835 ProS is also a good choice.

pfc + 740cc injectors + z32 + HKS GT2835 PRO S

Isn't 740cc overkill for anything under 350rwkw? 550cc injectors should be more than adequate.

Depends on how much power your after mate? and whether or not you may want more power in the future again!

again it depends on your supporting mods as well. sooner or later your going to need to change ur fuel pump, injectors, clutch, ecu...etc...and all of which costs more money.

imo, i'd go a HIFLOW. the hiflowed turbo will give you the best of both worlds, more power than stock and pretty good response as well. and best bang for buck!

my two cents,

goodluck mate

i would recommend the gcg hiflow, i had one of them on my rb25, got a vg30 ehxaust housing adapted to it and results were very good, i was more than happy with it. made 258kw at wheels on 15psi, my engine is built however but still expect a signifigant gain over standard turbo.

I'd go for a GCG highflow turbo. Personally tried and tested. Close to stock spool time, but huge power. It's ball bearing.

Bolts striaght up. No modding lines etc. Includes everythign you need e.g. gaskets, washers, etc etc.

Cheap -- 1750.

The precision turbo highflows in the group buy section are also good - 1550. ball bearing too. I personally haven't tested them, but I know people who have, and i'd get one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...