Jump to content
SAU Community

Recommended Posts

Over drive OFF, power button ON.

Step on the break, rev up to about 2000-2,500 REVs.

Let go off the break and step on it.

:pwned:

For a stock converter practice with various revs between 2000-2600rpm, & also don't rev till the last few seconds otherwise trans temps will soar faster than you can say 'V-TEC power yo!'.

:pwned:

For a stock converter practice with various revs between 2000-2600rpm, & also don't rev till the last few seconds otherwise trans temps will soar faster than you can say 'V-TEC power yo!'.

Yeah... also don't do this shit on every set of lights lol (I mean at the track) :pwned:

I have an Automatic... I chosen it as a preference as Auto's launch just as good as Manual if you know how... and in a straight line (with good mods), Autos will beat Manuals...

HEre's what you do...

OVER DRIVE OFF, POWER BUTTOM PRESSSED, MAke sure you are running High Octane fuel (I personally like BP'S ULTIMATE)... Put it on DRIVE... Hold the BRAKE... REV TO AROUND 3,000 RPM's... LEt go of the BRAKE, step on it until around 4,000 RPM's and then pull it back to 2nd Gear to maintain the REV's at around 5-6,000 RPM's... then you just hold on it and pull it back just before you redline it... this is pushing the car to it's full potential.. most races are quater mile... do the above right and you will OWN....

I've always wondered about that... how does a burnout work in a AWD car such as the GT-R? Is it even possible without wreaking the ATTESA and seriously heating up the oils in the diffs/clutches?

If you are going to push your auto at the lights by holding high revs on the brakes, you should first fit a auto trans cooler because you will be generating a lot of heat which is the best way to kill an auto trans. A few hundred insurance against a few thousand for repairs.

Over drive OFF, power button ON.

Step on the break, rev up to about 2000-2,500 REVs.

Let go off the break and step on it.

I've always wondered too how the Autos do it, as I'm in a manual I dont get it.

If you put it in DRIVE and rev to 3000 and hold the brake, wouldnt that just make the car do a burnout while at a standstill?

Then if you let go of the brake you'll just get wheelspin and take off?

I've always wondered too how the Autos do it, as I'm in a manual I dont get it.

If you put it in DRIVE and rev to 3000 and hold the brake, wouldnt that just make the car do a burnout while at a standstill?

Then if you let go of the brake you'll just get wheelspin and take off?

If you dont rev over 2500 revs the car just barely creeps forward. Hence why in the auto revving around 2000 rpm is the best.

When you let go off the brakes, you will hit boost much quicker (3500 revs) hence a better take off. At the end of the day if you have good tyres, there wont be a big burnout... however this all depends on like I said tyres and how much power you run.

My car is stock btw.

I have an Automatic... I chosen it as a preference as Auto's launch just as good as Manual if you know how... and in a straight line (with good mods), Autos will beat Manuals...

HEre's what you do...

OVER DRIVE OFF, POWER BUTTOM PRESSSED, MAke sure you are running High Octane fuel (I personally like BP'S ULTIMATE)... Put it on DRIVE... Hold the BRAKE... REV TO AROUND 3,000 RPM's... LEt go of the BRAKE, step on it until around 4,000 RPM's and then pull it back to 2nd Gear to maintain the REV's at around 5-6,000 RPM's... then you just hold on it and pull it back just before you redline it... this is pushing the car to it's full potential.. most races are quater mile... do the above right and you will OWN....

Keep that up and u will destroy ur transmission in no time.

thanks guys. been meaning to ask this question but keep forgetting that i wanna know. is it possible to do a standstill burnout in an auto as well?

Fully depress the break, then fully depress the accelerator and u will start spinning the wheels (or maybe 1 if u have a worn out lsd :(. Back off before u change gears or this will stop the burnout.

I've always wondered about that... how does a burnout work in a AWD car such as the GT-R? Is it even possible without wreaking the ATTESA and seriously heating up the oils in the diffs/clutches?

personally I just dont bother. If you *must* be fulli sik get one of thoes awd -> 2wd switch's that go's in the fuse box, if you have a 32, or dont bother, if you have a 33 - 34

I've always wondered too how the Autos do it, as I'm in a manual I dont get it.

If you put it in DRIVE and rev to 3000 and hold the brake, wouldnt that just make the car do a burnout while at a standstill?

Then if you let go of the brake you'll just get wheelspin and take off?

Use the handbrake. :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
×
×
  • Create New...