Jump to content
SAU Community

S/A Car Seat covers, Group Buy.


Recommended Posts

Guest MFX_R33

I have seen some interest in the Snap-On Style car seat covers. If there is an interest i can make them for the forum members with the Skylines Australia logo on them, for a very cheap group buy rate.

I do make them for alot of prominent companies around Sydney, and they are a quality product.

I can make them in Black, Blue, Purple, Red, Orange, Yellow, Pale Grey, and White.

If there is an interest of 10 or more, I can do them for a forum rate of $50 a pair.

Jeff.

Before I am shut down by moderators I am just offering this for a group benefit, if I am over stepping bounds, I appologise.

Link to comment
https://www.sau.com.au/forums/topic/16433-sa-car-seat-covers-group-buy/
Share on other sites

  • Replies 119
  • Created
  • Last Reply

Top Posters In This Topic

Guest MFX_R33

I don't have back one's yet, althoughI have been getting more call for them. The trouble is that it is harder to make 'one size fits all' rear seat covers, as some have headrests, some don't, some are big some are small.

So I am looking into it, but at the moment I don't do the rears.

Jeff.

I wouldnt mind some seat covers.

Would it be cheaper if a number of them are dumped at one of the customers house, then other customers living near by pick them up from there?

I'm thinking of this if a few northern beaches people order them.

Mark

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...