Jump to content
SAU Community

Recommended Posts

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

why has everyone gone for twins on a 'cheap' drag setup ?

go for a big single (garrett off the shelf). injectors, map sensor PFC, clutch, exhaust and ALOT of nos. i rekon you MIGHT just scrape in under 5K, with some second hand parts :)

Is that before or after you include the manifold you need, then custom dump/front pipe, custom piping/hosing oil/water lines etc etc etc etc etc.

Big squirt of gas. An ECU. open pipes and a cheap RB26 manifold with an XR6 turbo with some cheap injectors. If you can weld up the pipes yourself and get soem cheap 2nd hand slicks...then strip the hell uopt of it....maybe. But why woudl you bother when for 5k you could have a nice daily driver that runs flat 12s to high 11s ?

I will say it can't be done...just because if i say that some bugger will try to do it.

ill be the 1st to shake the hand of somebody who can acomplish this feat.

after a few broken engines and gearboxes they will agree with me...it can't be done.

It really not even worth trying. Even if you did everything yourself, even if you got all the parts you need under 5k, you'll be very lucky to get it off the line let alone make it down the quarter. Better to put in 10-15k if you can afford it and do it right rather than waste 5k doing it wrong.

It really not even worth trying. Even if you did everything yourself, even if you got all the parts you need under 5k, you'll be very lucky to get it off the line let alone make it down the quarter. Better to put in 10-15k if you can afford it and do it right rather than waste 5k doing it wrong.

Well said.

If this goes ahead, its likely the car will be f**ked in the process and the cost of then repairing it and doing the nessesary work to bring the thing back up to scratch will be huge.

Try and cut corners putting together a GTR and it WILL bite you in the ass, mark my words

It's one thing to talk about doing this to an XR6T which I presume is what is being discussed somewhere else and someone has said it can be easily done to a GTR. But there's one difference I think were all forgetting, A GTR is actually a good/rare car and ontop of that they aren't produced anymore, anyone who even thinks about butchering one just to prove a point is retarded. I'm happy for you to try it with an XR6T cos their becoming more popular than vl's and their still rolling of the production line, hell you could probably get most of the required parts at my local supermarket......

it will not

it will fail

TO4GTR has run an 11.2@121mph still using his original 210,000km+ engine with around 310rwkw. And he doesn't baby it at all :) Must be a freak engine.

I pesonally don't think it can be done for under 5k. Under 10k is very possible though.

I love all the expert replies from so many people that have ran 10's, according to my cousin all his mates cars run tens its easy

hahaha fools run the times consistantly then tell us how easy it is

consistancy aye buster, that why you've got an auto? :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...