Jump to content
SAU Community

modified 180sx 92

TRDsupra
 Share

Recommended Posts

TRDsupra Collaborator

TRDsupra

Posted
Posted

my mate have a 180sx fully modded bought from Japan not long ago. He's still waiting for the plate from the new scheme. He can't afford the new 4.5k plate since he bought it 3 weeks too late for the old scheme.

The car is a 92 180sx red with

sunroof

90,000kms

17" modena rims virtually unscratched

fmic from trust

hks boost controller

blitz boost guage

blitz turbo timer

momo steering wheel/ gear knob

upgraded fuel pump

upgraded clutch

aftermarket exhaust

mild bodykit

the only thing this car need is a bigger turbo to make 200rwkw

car willl be here roughly end of June.

Will be in melbourne and i have pics of his car

he's asking 15500 if you put down a deposit end of May or pay 17000 when the car gets here. Car cost him a bundle since it's all modded.

[email protected] or 0422 422 344

Link to comment
Share on other sites
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Pillowball/Hardened Runner Hybrid Approach

      By Duncan · Posted

      To add to that very useful summary, even in the race/rally r32 gtr I have good quality, new(ish) poly bushes everywhere because that is what rules require, and the handling is excellent. Of course, the car doesn't do many klm but I'd still expect poly bushes to last better in road use than sphericals (especially as I have a couple of klm of dirt road to stuff sphericals up) I would change the front upper arms to spherical if I was allowed to, because the poly bushes flog out often, but otherwise new bushes (and ball joints) and a good alignment can make a world of difference
    • joshuaho96
      ER34 AT ECU and HKS SLD pins

      By joshuaho96 · Posted

      Any chance you can get a Nistune board installed instead and set the speed limit to whatever your tires can handle?
    • GoHashiriya
      ER34 AT ECU and HKS SLD pins

      By GoHashiriya · Posted

      Hi all, I need to get this HKS SLD attached to my stock ECU because I've now got the German autobahn and faster European circuits to contend with.  The car is a manual 2dr ER34 with an AT ECU and I've realised the AT ECU has two pins for speed sensor signals: Pin 29: Vehicle speed sensor signal (Vehicle speed sensor 2) Pin *58: Output shaft rotation sensor signal (Vehicle speed sensor 1) - *RB25DET A/T model only Before I go butchering this harness, is anyone sure of which pin is the correct one for signal adjustment? The attached document from HKS indicates pin 29 but I found this situation mentioned in the following thread on a different forum (R34 GTT Auto Trans Speed Cut Problem | Zerotohundred) mentioning pin 58 needing to be altered by member zephuros, albeit it seems to be for an RSM-GP and the info appears to be old.  R34_All_Workshop_Manual-pages-2.pdf R34_All_Workshop_Manual-pages-3.pdf R34_All_Workshop_Manual-pages-1.pdf HKS SLD Vehicle Pin out P59-P70 ER34-pages.pdf
    • dyl33
      Creative in cabin amp locations

      By dyl33 · Posted

      Slimline sub on the rear parcel shelf is doable. Pioneer TS-WX140DA is only 70mm high.   
    • GTSBoy
      Rear suspension upgrades

      By GTSBoy · Posted

      People like Johnny Dose Bro might be laughing at my post because I accidentally added 100mm to my numbers. 350-355 is indeed the lower limit. 450 is off-road Skyline spec.
×
×
  • Create New...