Jump to content
SAU Community

Non Turbo 32 Or 33

Adz2332

By Adz2332,
in Engines & Forced Induction

 Share

Recommended Posts

Eug Grand Master

Eug

Posted
Posted

no idea to be honest... i personally would have paid up to $13-14k for it.

there's not much of a market for them really, it's flooded with $8-11K garbage. not to mention the fact that every other wannabe would rather/can get a 200rwkw for next to nothing.

the clean, straight, low km, stock examples are far and few between.

Powers Lacking Contributor

Powers Lacking

Posted
Posted

Hey just recently sold my R33 gts25 for $10.2k to the gf had it advertised for 11.5k but was getting next to no response. 1994, full 2.5 inch zorst, pod, steering wheel, 18s body kit and 92xxx genuine kms.

When selling mine found there was not much of a market for non turbo's so u should be able to pick one up quite cheap-cheap i say!

thorpe84 Proficient

thorpe84

Posted
Posted

i payd $11,500 for a 97 series 2 r33 non turbo AUTO. very very clean, from a car dealer, shitty 4 month warranty but anything is better then nothing and im the first owner in australia.

the reason i got an auto was because it was alot cheaper then the manual and for a first car i really couldnt be botherd getting a manual license,il drive manual when its worth driving (turbo)

anyway all in all mine is in very good condition and is perfect for what i need it for. a daily driver, something that looks good and has a little more power then most and is very easy to drive with decent fuel consumption.

for what its worth dont get an r32 they are very old (almost 20 years old!!!) and becomming very outdated. especially if your dealing with non turbo/non performance skylines then newer is better.

R-SPEC Grand Master

R-SPEC

Posted
Posted

sold my n/a about 4 months ago.

it was a black 1993 r33 gts4 automatic.

had a full kit.

87,000Ks

excellent condition all round, interior was closest thing to brand new.

dual airbags (driver/passenger)

sold it for $8000 with rwc and 3months rego.

personally i'd never pay more than that for an n/a skyline.

  • 2 weeks later...
mad082 Grand Master

mad082

Posted
Posted
pod filter, exhaust, extractors is alot more grunt then a r33

somehow i doubt that that would give you a 26kw gain. if it did it would only make it similar in power to a 33. then do the same mods to a 33 and it will have much more power than the 32.

stock NA 33 = 104kw/ton

stock NA 32 = 94kw/ton

stock vx commodore = approx 98kw/ton

are33 Proficient

are33

Posted
Posted (edited)

I bought my 33 from a dealership on the gold coast, MJR Motorsports, They are excellent for importing stock clean low k's cars.

Mine is a 1997 R33 GTS25 Series 2, It had 40,xxx KLMS when i bought it, ive done 4000 so far, it was 100% stock when i bought it, So far ive only put a cat back exhaust on it.

It dynoed in at 160HP/116KW At the wheels with the cat back exhaust only.

I paid $16,500 for it, A bit pricey yes, But if you see my car you would understand, Exterior, Interior and engine bay is next to showroom condition.

Edited by OBNXSH
  • 2 months later...
Caza Enthusiast

Caza

Posted
Posted (edited)

i have i r32 gts silver id sell very clean new respray been in an accident still getting fixed all i hit was a gutter an bent a few arms thats it, soo no chassis damage or body except the front gaurd got a scrape on the ground and is all being repaired as we speak

i need a work ute thats y im selling dont really want to but the sooner the better i suppose........

thats it in my pick

Edited by Caza

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...