Jump to content
SAU Community

Recommended Posts

no idea to be honest... i personally would have paid up to $13-14k for it.

there's not much of a market for them really, it's flooded with $8-11K garbage. not to mention the fact that every other wannabe would rather/can get a 200rwkw for next to nothing.

the clean, straight, low km, stock examples are far and few between.

Hey just recently sold my R33 gts25 for $10.2k to the gf had it advertised for 11.5k but was getting next to no response. 1994, full 2.5 inch zorst, pod, steering wheel, 18s body kit and 92xxx genuine kms.

When selling mine found there was not much of a market for non turbo's so u should be able to pick one up quite cheap-cheap i say!

i payd $11,500 for a 97 series 2 r33 non turbo AUTO. very very clean, from a car dealer, shitty 4 month warranty but anything is better then nothing and im the first owner in australia.

the reason i got an auto was because it was alot cheaper then the manual and for a first car i really couldnt be botherd getting a manual license,il drive manual when its worth driving (turbo)

anyway all in all mine is in very good condition and is perfect for what i need it for. a daily driver, something that looks good and has a little more power then most and is very easy to drive with decent fuel consumption.

for what its worth dont get an r32 they are very old (almost 20 years old!!!) and becomming very outdated. especially if your dealing with non turbo/non performance skylines then newer is better.

sold my n/a about 4 months ago.

it was a black 1993 r33 gts4 automatic.

had a full kit.

87,000Ks

excellent condition all round, interior was closest thing to brand new.

dual airbags (driver/passenger)

sold it for $8000 with rwc and 3months rego.

personally i'd never pay more than that for an n/a skyline.

  • 2 weeks later...
pod filter, exhaust, extractors is alot more grunt then a r33

somehow i doubt that that would give you a 26kw gain. if it did it would only make it similar in power to a 33. then do the same mods to a 33 and it will have much more power than the 32.

stock NA 33 = 104kw/ton

stock NA 32 = 94kw/ton

stock vx commodore = approx 98kw/ton

I bought my 33 from a dealership on the gold coast, MJR Motorsports, They are excellent for importing stock clean low k's cars.

Mine is a 1997 R33 GTS25 Series 2, It had 40,xxx KLMS when i bought it, ive done 4000 so far, it was 100% stock when i bought it, So far ive only put a cat back exhaust on it.

It dynoed in at 160HP/116KW At the wheels with the cat back exhaust only.

I paid $16,500 for it, A bit pricey yes, But if you see my car you would understand, Exterior, Interior and engine bay is next to showroom condition.

Edited by OBNXSH
  • 2 months later...

i have i r32 gts silver id sell very clean new respray been in an accident still getting fixed all i hit was a gutter an bent a few arms thats it, soo no chassis damage or body except the front gaurd got a scrape on the ground and is all being repaired as we speak

i need a work ute thats y im selling dont really want to but the sooner the better i suppose........

thats it in my pick

Edited by Caza

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...