Jump to content
SAU Community

Adjustable Upper Arms - Problem R32 Gtr

Ronin 09
 Share

Recommended Posts

Ronin 09 Grand Master

Ronin 09

Posted
Posted

My R32GTR runs with coilovers (around 355mm front guard height).

I have adjustable front upper arms, and have around 1 deg neg set up.

This means that the upper arms are quite extended (to reduce the neg camber when it is lowered).

The problem is that the outers of the arms are fouling the inner guard, and actually have bent the lip of the inner guards a bit...

How does one fix this problem, without running a lot of front camber?

The pics should make it clearer...

gallery_1486_103_42594.jpg

gallery_1486_103_183898.jpg

salad Veteran

salad

Posted
Posted (edited)

May sound stupid, but are the in the right way?

I had this problem when I got my upper arms, turns out I put them in upside down, gave me lots of castor and not much camber. :)

Flipped the arms around and can easily run 1deg camber at 350mm ride height with no issues of fouling.

Edited by salad
Ronin 09 Grand Master

Ronin 09

Posted
  • Author
Posted

interesting... can you do me a favour and see if the fat part (i.e. the female side) is on the outside like we have on mine, or the skinny part (ie. the male side) is on the the outside of yours?

cheers Showza!

salad Veteran

salad

Posted
Posted (edited)

Ah bugger, mine are different to yours though, mine are a turnbuckle style arm. But would only fit in one way anyway, one end is slightly wider than the other.

Only thing I can think of is are the arms staggered the right way? As they look like ---> I they should be staggered so the upright is pulled foward as far as possible. The body end looks right, but cant really tell for the upright end. But seems a bit odd that the arms themselves would be around the wrong way...

Edited by salad
B0oStEr Mentor

B0oStEr

Posted
Posted

Now you've got me worried.

I fitted adjustable bushes to my upper arms yesterday and I'm waiting to have a wheel alignment on tuesday to set my camber at neg 1 deg with 345mm ride height.

The arm looked like it might go close but I thought it would be ok because I had never heard anyone say they had a problem... until now.

Come to think of it I thought the suspension felt rock hard when I tried to bounce it.

I thought it was the new bushes being really tight but now I'm thinking I may have your problem.

blind_elk Grand Master

blind_elk

Posted
Posted

Are you sure you have NEGATIVE camber. I would have expected the adjustment to be compressed to give negative, ie shortening the arms will pull the upright, and thus the top of the wheel, in towards the centre of the car.

Ronin 09 Grand Master

Ronin 09

Posted
  • Author
Posted
This may sound stupid - but the stock ones are handed.

Did you put the right one on the right hand side & the left one on the left hand side?

Also what is your ride height & how much castor are you running?

Yep i checked the fitting guide and there is only one way they can fit with the adjusters on the top.

Ride height is 355ish and the castor rods are standard.

something about those arms looks odd, do they have any offset like the std arms? almost like the upper arm is swinging in the wrong area under guard...

They are offset like the standard arms, you can see that the top pic is the RHS and the second pic is the LHS. In the LHS pic you can see the offset bit in the top right of the pic

The shock mount simply holds the shock absorber - it has absolutely no bearing on camber.

Ronin - did that 1 deg neg come from a wheel alignment machine?

Yep it was done on an alignment machine. It may have slipped though if they weren't done up tight enough - It's getting towed to the workshop tomorrow so hopefully can sort it out.

Many thanks everyone for the replies, keep them coming!

:)

MrStabby Grand Master

MrStabby

Posted
Posted

I have the same adjustable arms - if mine were extended as far as yours are they would foul the guard as well. I have 1 deg neg camber but the arm is only about half way extended, and i have about 10mm clearance. IIRC my car is around 345mm hight, which should mean i need to extend the arm more, not less, so NFI whats going on with your setup... If you're in Sydney and want to check out my install, let me know.

GTRsean Grand Master

GTRsean

Posted
Posted

Mine did that when I asked them to wheel align my car at -.5 deg camber. It made a knocking sound every time I hit a bump. Had to knock bit of metal straight and prime, paint exposed metal.

I triple checked that I installed them correctly.

I think They don't like anything less than -1.2deg or so depending on alignment of vehicle.

Beer Baron Grand Master

Beer Baron

Posted
Posted

the arms are definately installed properly, and it looks like it's the upright hitting the gaurd not the arms. the only way out here is run more neg. so hardnen up boyo and run more neg.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...