Jump to content
SAU Community

Recommended Posts

Hey just me again,

Thanks once again for the part no's you were able to get for me last week they were tops and i ordered and fitted the parts from Nissan on the weekend!

Just another quick question for the Injector Sealing O-rings are they the same part on the r33 gtr as on the r32 gtr, (16636-V5000) or another no altogether, and are they the seal between the fuel rail and the injector head? As that's the part i'm after!

Many Thanks once again,

All your help here with Part #'s is excellent!

skysaresilver

The o-ring seals on the injectors are all the same. The bigger seals at the top of the injector head where they fit into the fuel rail don't actually seal anything. They are there to act more or less like a shock absorber. The only seals to worry about are the o-rings.

That was actually going to be my next quesiton.

After looking in the workshop manual they say to change the insulators as well as the o-ring.

Do you have the insulator number as well?

Seeing as I am changing them to try and track down a running issue, I figure I might as well change all.

Thanks.

David

Oh and can you give me the part number for the coolant temp sensor (looks like the air temp sensor in the plenum).

Can can you verify if they are the same sensor for both coolant temp and air temp?

Thanks.

D.

Thanks Ron, I really appreciate it. :action-smiley-069:

Do you know if the coolant temp sensor is the same part number as the air temp sensor in the plenum?

Thanks.

If you ever come to the Bahamas, I will definitly by you a pint. :P

D.

I searched for the air temp sensor but only found air bag sensors. Mind you i was stuffed last night. I'm thinking it could be an exhaust temp sensor (even though its located before the exhaust) the program can be funny like that I reckon.

Can anybody that know's which part we are looking for help out?

Hey all, and i big hello to AREP3

I apologise for my disappearance from the forums. I no longer have the time to commit to posting part numbers on the board, but i will do what I can, so what i would suggest is do a search on the forum for what you are after as they will be scattered throughout the place.

Ill be back here and there.

AREP3, your doing a marvelous job here! if only i could nominate you for a logie.

kind regards,

Arbess

Thanks Ron, I really appreciate it. :P

Do you know if the coolant temp sensor is the same part number as the air temp sensor in the plenum?

Thanks.

If you ever come to the Bahamas, I will definitly by you a pint. :)

D.

Had another look mate and all I can get is the same part number so i'm GUESSING that they are the same part.

Hey I have a double request:

R33 Gtst - inlet cam gear with VCT 13024-42L02-

R34 Gtst (NEO) - inlet cam gear with VCT13024-5L300-

Want to see if they're the same.....fingers crossed.

Not the same sorry mate

Hey I have a double request:

R33 Gtst - inlet cam gear with VCT

R34 Gtst (NEO) - inlet cam gear with VCT

Want to see if they're the same.....fingers crossed.

Can i also enquire about:

R32 gstst - inlet cam gear with VCT

Cheers

Dane

Hi there

I want to know the part number of the two arms that hold up the boot lip for a R34 GTT 4DR...and also will i be able to order a repair manual from nissan for my car...Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
    • Unsolicited advice? Keep the engine as close to stock as you can. Nothing wrong with adding some boost and making a little more power, but given where you are, you really don't want to try to make it into a monster. I can't imagine the roads are up to it, and the lack of locla support when it grenades will be a ball ache. FWIW, If there is a dyno around that you can access, then brand new injectors are a good idea, which will lead you to (at least) putting a Nistune in it, which will allow you to put an R35 AFM on it, all of which will make it possible to make it much much nicer to drive and live with.
×
×
  • Create New...