Jump to content
SAU Community

Nissan Genuine Part Numbers

arbess

By arbess,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

  • Replies 707
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

arbess
arbess

This will look a little plain but as soon as i can get some general parts together I will list them. check back soon -------------------------------------------------------------------------------

Posted Images

arep3 Experienced

arep3

Posted
Posted
Just the hoses :thumbsup:

i believe that any generic rubber hose from any auto shop would suit the job just fine. a lot cheaper and quicker then ordering the genuine parts from japan

Link to comment
Share on other sites
skysaresilver Community Regular

skysaresilver

Posted
Posted

HI THERE,

JUST AFTER SOME PART NISSAN PART NUMBERS FOR A R32 GTR 90' MODEL.

1. THE RUBBER SEALS WHICH GO AROUND YOU ROCKER COVERS - PRESUME THEY MAY COME AS A KIT BUT COULD BE WRONG ON THAT ONE? AND

2. THE REAR GEARBOX RUBBER MOUNT, (HOLDS THE GEARBOX AT THE RIGHT HEIGHT BETWEEN WHERE THE BAR GOES ACROSS THE CAR IN THE MIDDLE AND THE BOTTOM OF THE REAR OF THE GEARBOX).

MANY THANKS IN ADVANCE!

ADRIAN. >_<

Link to comment
Share on other sites
arep3 Experienced

arep3

Posted
Posted
HI THERE,

JUST AFTER SOME PART NISSAN PART NUMBERS FOR A R32 GTR 90' MODEL.

1. THE RUBBER SEALS WHICH GO AROUND YOU ROCKER COVERS - PRESUME THEY MAY COME AS A KIT BUT COULD BE WRONG ON THAT ONE? AND

2. THE REAR GEARBOX RUBBER MOUNT, (HOLDS THE GEARBOX AT THE RIGHT HEIGHT BETWEEN WHERE THE BAR GOES ACROSS THE CAR IN THE MIDDLE AND THE BOTTOM OF THE REAR OF THE GEARBOX).

MANY THANKS IN ADVANCE!

ADRIAN. >_<

please look at this and tell me that these are the parts you need. i will supply you with part numbers if they are.post-14067-1186364698_thumb.jpg

i haven't been able to find the gearbox mounts. i do know that you can get the nismo 1s from justjap. Gearbox mounts

maybe arbess will be able to find the genuine 1s for you.

Link to comment
Share on other sites
arep3 Experienced

arep3

Posted
Posted
1990 R32 GTS4

drivers side propella shaft rubber boot (shaft to front diff housing)

Picture added to help clarify the part:

post-32703-1186319346_thumb.jpg

im not sure what part your after. i dont know of any rubber boots like that on the front driveshaft. steering rack maybe?

Link to comment
Share on other sites
skysaresilver Community Regular

skysaresilver

Posted
Posted
please look at this and tell me that these are the parts you need. i will supply you with part numbers if they are.post-14067-1186364698_thumb.jpg

i haven't been able to find the gearbox mounts. i do know that you can get the nismo 1s from justjap. Gearbox mounts

maybe arbess will be able to find the genuine 1s for you.

Yep, those are the two gaskets i'm chasing which you have highlighted in green would there be any chance you could get the part numbers for these that i have to go to Nissan with to order them direct - i was also going to chance the half moons whilst i was in there replacing the rocker gaskets - so the parts i'm chasing are:

1 x 13270

1 x 13270 + A

2 x 11051H

I'll also grab that gearbox mount from justjap so thankyou very much for the link to that page, it's greatly appreciated!

Many Thanks,

Adrian aka skysaresilver

Link to comment
Share on other sites
arep3 Experienced

arep3

Posted
Posted
Yep, those are the two gaskets i'm chasing which you have highlighted in green would there be any chance you could get the part numbers for these that i have to go to Nissan with to order them direct - i was also going to chance the half moons whilst i was in there replacing the rocker gaskets - so the parts i'm chasing are:

1 x 13270

1 x 13270 + A

2 x 11051H

I'll also grab that gearbox mount from justjap so thankyou very much for the link to that page, it's greatly appreciated!

Many Thanks,

Adrian aka skysaresilver

1 x 13270 = 13270-58S01-

1 x 13270 + A = 13270-58S11-

2 x 11051H = 11051-58S00-

>_<

Link to comment
Share on other sites
ROB32T Collaborator

ROB32T

Posted
Posted

hey mate

just after part numbers for R32 gtst 93

idler pulley

tensioner pulley

water pump

timing belt

are these part numbers the same as a r33 cause i've heard they are the same

thanx

Link to comment
Share on other sites
Kaz200 Grand Master

Kaz200

Posted
Posted
hey mate

just after part numbers for R32 gtst 93

idler pulley

tensioner pulley

water pump

timing belt

are these part numbers the same as a r33 cause i've heard they are the same

thanx

21010-70T25 - RB20DET water pump (or try 21010-42L25)

13028-20P25 - RB20DET timing belt

13074-58S00 - RB20DET idler pulley

13070-53L00 - RB20DET tensioner pulley (or try 13070-73L00)

Water pump is approx $110 retail from Nissan

You are better off getting some Gates or CBC bearings/pulleys as OEM you can expect to pay $250+ for each

Autobarn for eg, can order in a kit for you fairly cheap and it also includes the oil seals, but CBC bearings are better quality and a little more expensive (still cheaper than Nissan though)

Also the Gates Racing timing belts are about the same price as a standard OEM belt

Are you doing the 100k service?

Link to comment
Share on other sites
ROB32T Collaborator

ROB32T

Posted
Posted

you are a legend :P

I'm trying to find a noise and had to take my balancer off in the process so i thought I might aswell do it again. maybe if i'm lucky it will get rid of the noise too.

nah not going to nissan. bearing industries couldn't find the part number for rb20's.

thanx heaps :thanks:

Link to comment
Share on other sites
FighterJoe Explorer

FighterJoe

Posted
Posted (edited)
thanks mate for the info.. :D

No probs. ;)

need part number for a o2 sensor for a '95 model series 2 rb25det?

R33 RB25DET 02 sensor part numbers:

08/1993 - 11/1993 number : 22690-21U00 (alt number 22690-83T10)

11/1993 - 01/1996 number : 22690-83T10

01/1996 - 11/1997 number : 22690-83T10 (same)

11/1997 - number : 22690-83T11

Edited by FighterJoe
Link to comment
Share on other sites
i4dat Apprentice

i4dat

Posted
Posted

Excellent thread! :D

I need some help also for the following:

1996 R33 GTR

BCNR33-024671

Injector sealing O-rings

Intake Plenum Gasket

AAC Valve Gasket (maybe the same as this? 23785-40F00)

Driver Door Seal

Passenger Door Seal

And finally... the little GTR Square plug that goes by the coin holder on the center console behind the shifter boot.

Thanks in advance. ;)

David.

Link to comment
Share on other sites
FighterJoe Explorer

FighterJoe

Posted
Posted (edited)
Excellent thread! :D

I need some help also for the following:

1996 R33 GTR

BCNR33-024671

Injector sealing O-rings

Intake Plenum Gasket

AAC Valve Gasket (maybe the same as this? 23785-40F00)

Driver Door Seal

Passenger Door Seal

And finally... the little GTR Square plug that goes by the coin holder on the center console behind the shifter boot.

Thanks in advance. ;)

David.

For BCNR33-024671 (Nov 1996)

Injector sealing O-rings - Insulator-injector number: 16636-V5000

Intake Plenum Gasket - Intake manifold gasket number: 14035-05U10 (assuming intake manifold gasket not throttle chamber gasket which is 16175-05U70)

AAC Valve Gasket (maybe the same as this? 23785-40F00) - AAC gasket number: 23785-40F00 (yep same as the one you quoted)

Driver Door Seal - Right hand door weather strip number: 80830-22U00

Passenger Door Seal - Left hand door weather strip number: 80831-22U00

the little GTR Square plug that goes by the coin holder on the center console behind the shifter boot - Switch hole mask number: 68960-24U00

Edited by FighterJoe
Link to comment
Share on other sites
skysaresilver Community Regular

skysaresilver

Posted
Posted
For BCNR33-024671 (Nov 1996)

Injector sealing O-rings - Insulator-injector number: 16636-V5000

Intake Plenum Gasket - Intake manifold gasket number: 14035-05U10 (assuming intake manifold gasket not throttle chamber gasket which is 16175-05U70)

AAC Valve Gasket (maybe the same as this? 23785-40F00) - AAC gasket number: 23785-40F00 (yep same as the one you quoted)

Driver Door Seal - Right hand door weather strip number: 80830-22U00

Passenger Door Seal - Left hand door weather strip number: 80831-22U00

the little GTR Square plug that goes by the coin holder on the center console behind the shifter boot - Switch hole mask number: 68960-24U00

Hey just me again,

Thanks once again for the part no's you were able to get for me last week they were tops and i ordered and fitted the parts from Nissan on the weekend!

Just another quick question for the Injector Sealing O-rings are they the same part on the r33 gtr as on the r32 gtr, (16636-V5000) or another no altogether, and are they the seal between the fuel rail and the injector head? As that's the part i'm after!

Many Thanks once again,

All your help here with Part #'s is excellent!

skysaresilver

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • klutched
      GOT SUM's RB34

      By klutched · Posted

      This morning I carefully reinstalled the manifold and started looking at a couple of things I need to do.  Heat wrap arrived sometime today so I popped into the shed with the missus dishwashing gloves and started wrapping the first half of the dump and the screamer/plumb back.  Once I do the second half I'll be able to final fit the turbo and exhaust up.  Also pulled the harness out today and started terminating it at the ECU end. A connector is done, just need to run the remaining wires that arent in the harness - 12v, gnd and couple I/O
    • Dose Pipe Sutututu
      Rear suspension upgrades

      By Dose Pipe Sutututu · Posted

      A31 is pretty much the same thing without HiAIDS I mean CAS, no improvement lol. Not to late to send it.
    • carnoobb
      Newbies

      By carnoobb · Posted

      Thanks for all the replies! I also wanted to ask if wheels that were fitted on Ford Falcons would fit the 350GTs as well? In the area I'm at there aren't that many options for secondhand wheels and new ones here are way out of my budget. From what I've seen, most of the wheels that are available that were fitted on Ford Falcons have an offset of +33 to +36, with a centre bore of 70.5mm whereas the stock 350GT's ones are 66mm, can't seem to find any hubcentric rings that fit that difference though. 
    • sonicii
      Newbies

      By sonicii · Posted

      215/45/18 tyres are probably a little on the low side compared to the factory tyre, it should be closer to a 245/45/19, which will get you about an extra 11mm of height, and should make you speedo read a bit closer to reality. 245/45/19s will be a bit too far the other way and you risk a speeding ticket as your speedo might read slower than your actual speed.  245/40/19s would be correct if you are going to 19in rims, they will give you a similar total diameter to the 245/45/18 tyres.  
    • GTSBoy
      Rear suspension upgrades

      By GTSBoy · Posted

      That's something I forgot to put in my list. The aggressive anti-squat in R32 is a f**king menace. I still need to decide if I'm going to drag the subframe out of my car and weld in the GKTech corrector kit. The main reason to dither is the need to switch to spherical joints in the lower arm to account for the twist induced in the rear pivot caused by lowering the front pivot. And yes...we do put better subframes in R32s, and I wish I'd gotten an S14 one instead of an A31 when I did the "take off and nuke it from orbit" HICAS delete all those years ago.
×
×
  • Create New...