Jump to content
SAU Community

Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

My understanding is the same as Ben's. As another analogy (an exaggerated one to help illustrate the point), imagine two different-sized air tanks. One maybe the size of a Coke bottle, the other the size of the tank on the back of a petrol tanker.

Pressurise both to a given pressure, say 20psi.

They're both at 20psi PRESSURE, but the difference in VOLUME is massive.

I always like the water tank analogy.

You got a big water tank full of water

you punch a small hole in the bottom of it with a nail - how much water comes out ?? Not much.

then you get a huge hole saw and put a 5 inch hole at the bottom - how much water comes out ?? Heaps

The pressure in each circumstance was the same - 1 bar (Atmospheric pressure I think is 1 bar)

Correct, 1 bar or 14.7psi IIRC is atmospheric pressure at sea level.

An interesting side note which many people don't think about is that as a result, when your boost gauge shows, for example, 1 bar of boost, the intake manifold is actually at 2 bar, because you're adding 1 bar of BOOST to the 1 bar of atmosperic pressure.

I guess that means drivers of NA vehicles could tell people they're running 1 bar through their motor... :)

Yes, just like if a tree falls in the woods, does it make sound??? :confused:

Back to the question from evl r33, don't look at numbers from differing dyno's and base everything on them. They are simply a tuning device. My car made 160kw on rwd but then suddenly made 180kw on 4wd at a different place? That's right, the transmission somehow makes power now... :confused:

Originally posted by fatz

kinks

give me 10 seconds and i will show you how to drive a GTR

then you will know how txo get it sidways

pete

I've been for a ride with you in the streets of mudgee, you took blackbart and I for a spin. Ages ago :D

Back to the topic at hand - Tex and I were debating this last night. When you're talking about how much power an engine's making in terms of the turbo side of it you care about two main things - boost pressure and intake air temperature. Remember that boost pressure is measured at the manifold, after the throttle body. Same with intake temp. At that point, everything else is constant because the heads are the same as before, the cylinder filling will be the same. This means that for a given manifold pressure you will get a constant VOLUME of air going into the engine whether your turbo is big small or spraypainted bright purple. With a bigger turbo, the air isn't heated as much and therefore because it's denser, you get more MASS air flow into the engine - which at the end of the day should give you more power.

As for why two stock turbos running 1 bar gives more power than two bigger turbos running 1 bar I'm not sure. It must come down to tuning differences or - more likely - dyno differences. Remember that dynos aren't comparable a lot of the time - you only have to see Secoh's "dyno proven" 195rwkW VW Beetle to know that dynos can tell fibs. (although I think that power figure was wind assisted) :P

You also have to remember a large turbo is going to give you a cooler charge of air aswell as an increased volume.

The cooler the air is the more dense it is.

So more cooler air = more power :O

Also another thing to note is peak power is not the only thing that matters the area under the power curve is what makes a difference to. The large the area under the curve you have a larger power band.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...