Jump to content
SAU Community

Recommended Posts

was that a spray can or compressor and spray gun job on the interior dane?

i did mine (all the interior and cage) with a pressure pack (matched to factory code)...

post-5400-1226897738_thumb.jpg

That came up well Stu. Some nice prep work :banana:

Spray can my friend. It all turned out pretty well, bar the rear guards because I was too lazy to get all the glue off... oops :(

Gts30: An hour? Nice one! I bought maybe 4kg's for the rear seats forward, and then did the tranny tunnel with a heat gun, same with the rear guards. Would have been easier without the cage in there, and at my premesis instead of a workshop with limited light/time.

Ben: Do it! Would look tough as nails. Are you putting GT-R guards on?

Fark yeeeeeeah maaaaaaaate *throws can*

post-8405-1226904008_thumb.jpg

That is just about THE s15 as far as im concerned.

Funky, ok maybe 2 hours tops, I had also already done the back wheel arches and where the seat would go with the heat gun. Im painting the cabin and boot the same color as the rest of the car over xmas.

Tough as nails that S15!

I'd love to say i am putting GTR bits on it, but I don't think the rules allow, and its just more expensive when it goes into the scenery. And it already owes too much. Shoulda known, no such thing as a cheap race car.

Just finished putting the cooler on though :( Awesome hey! lolol

cooler2.jpg

yeah, I'm cutting more reo......

update on my engine hopfully be done this week :ph34r: then should be getting new seats and cage put it; if everything goes to plan should hit the track in dec so i can get a time and start tuning up the suspension

Also had the car up on the hoist and found that some sections of the exhaust were very very average on joining/welds; so redoing the exhaust, hopfully net me afew more hp

image000qy6.jpg

Edited by [Michael]

that is a seriously tuff s15. when i was thinking flat black there is apparently a clear flat that they put on over the top layer of black and it doesn't suffer finger prints etc so no need to repaint all the time. i only wanted to do it this way else it would look crap pretty quick i reackon as flat black dis-colours with uv light.

marlin - you're a reo

Cheers Matt.

Stu: That would be pretty sweet, I dig satin black a lot. I think if I ever had to repaint my whole car I'd do that... or Gulf livery :P But let's hope it doesn't come to that anytime soon

Also, I put someone on to you about some Bmax's from NS.com, so he should be contacting you soon.

Mick: That'll look good mate. I'm glad mine is done though, prepping and painting sucks :)

Ben: Does it do chirpies in second now?

update on my engine hopfully be done this week :P then should be getting new seats and cage put it; if everything goes to plan should hit the track in dec so i can get a time and start tuning up the suspension

Also had the car up on the hoist and found that some sections of the exhaust were very very average on joining/welds; so redoing the exhaust, hopfully net me afew more hp

image000qy6.jpg

nice. :P is that my old head?

Anyone know any fabricators who would want to make this for me? I had one lined up for the last two months, but it's just fallen through... doesn't need to be exactly the same, just a box with a perspex lid on it for my fuel system.

ASE-FUELSAFE3.jpg

Dane, you should try ASE in adelaide...

I had my custom catch can done by them, they also make the overflow bottles...

tidy work, i doubt a one off item will be super cheap though...

alternatively, if you made a cardboard template first, almost any fitter and turner/engineering place would be able to make it for you quite cheaply...

eg:

http://www.truelocal.com.au/business/i-and...ty-ltd/richmond

A friend of mine has a cousin that works at the place in that link, they mainly do large scale jobs.

He may be able to do it on the side, as in after hours type of thing.

(although turn around time is usually slow for that type of thing)

I can put you on to him if you want... pm me.

quick random dyno comp video here - http://www.youtube.com/watch?v=7vamwKMA2DU

and a small video of me giving it a hit in 1st and 2nd - http://au.youtube.com/watch?v=9J7VsRUVC9M

All work is done at GT AUTO GARAGE and tuned on a dyna pack dyno

Engine: RB25

STANDARD ENGIN

STANDARD CAMS

STANDARD HEAD

Modifications:

HKS TO4r Turbo KIT

HKS super drager exhaust

HKS S type intercooler

Apexi AVCR boost controler

Apexi Power FC

Apexi turbo timer

Sard 850cc injectors

Greedy type RS bov kit

600hp walbro intank fuel pump

Excedy clutch

PWR engin oil cooler

PWR power steering oil cooler

Tein flex (with pillow top mounts) coilovers

Tein EDFC

OZ RACING light weight racing wheels 17 x 9 inch

EBC slotted rotors (front_

EBC red stuff pads (front

EBC green stuff pads (rear)

PROJECT MU SCR rotors (rear)

Bridgestone RE55 semi slick tires 245/40 front

Bridgestone RE55 semi slicks 255/40 rear

CUSCO 7 point roll cage

CUSCO struct bars

GTR front bar

Carbon boot lid

Sparco seats

Power:1 bar = 299 kw (401 hp) @ tires

weight 1310kg with 1/4 tank of fuel

corner weight 58% front/ 42%rear

post-19157-1227765305_thumb.jpg

post-19157-1227765451_thumb.jpg

post-19157-1227765602_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...