Jump to content
SAU Community

Recommended Posts

R33 Series 2, GTS-T Manual, stock apaprt from turbo back exhaust & k&n POD filter

ok, still hesitating/surging after 4500rpm, cant work out what it is, so far the following has been replaced (not neccisarily to fix this problem)

fuel pump, plugs, coil packs, fuel filter, timing belt, water pump, k&n filter, clutch, injectors cleaned, serviced, turbo back exhaust

it went on the dyno yesty and it showed no change in the air/fuel mixtures when it was surging,

so is it coil pack igniter module thingy? timing? ?????????

Link to comment
https://www.sau.com.au/forums/topic/178121-whats-wrong-with-my-car/
Share on other sites

what heat range plugs?

what gaps?

coil packs new?

you haven't mentioned anything about the AFM.

i know the plugs are platinum ones, the gaps are right and the coil packs are new (splitfire)

i thought if the air flow meter was playing up it would of shown a change in the air/fuel mixtures when it was surging???

get rid of the platinum plugs. they are terrible.

get coppers (part number bcpr6es) or iridiums. if you get iridiums make sure they are gapped to 0.8mm and heat range 6.

ok they may be crap, but could they be actually causing the problem? especially this noticable.

Edited by walta

slose gapped plugs shouldnt be required if you got new splitfire coils, should have ample spark to jump even the stock 1.1mm gap... look elsewhere for your problem, disconnect each coill pack via the plug and reconnect n go through the list as its running to varify which cylinder has the miss and work from there

slose gapped plugs shouldnt be required if you got new splitfire coils, should have ample spark to jump even the stock 1.1mm gap... look elsewhere for your problem, disconnect each coill pack via the plug and reconnect n go through the list as its running to varify which cylinder has the miss and work from there

I agree, its not like your running monster boost or anything. I would have thought stock gap would be fine, but if it isn't, mabye becuase of your exhaust, then I wouldn't really think that you'd need anything smaller than .08mm.

Hey guys

Just throwing this out there but could it be something to do with the CAS??

Yes, i was getting a bad miss on mine, tried a few things like coil packs, AFM, spark plugs, etc....

Got a CAS from another skyline and put it on mine, miss was gone. Grabbed a 2nd hand CAS and threw it on.

Yes, i was getting a bad miss on mine, tried a few things like coil packs, AFM, spark plugs, etc....

Got a CAS from another skyline and put it on mine, miss was gone. Grabbed a 2nd hand CAS and threw it on.

whats a CAS by the way? LOL

hi just throwing it out there.

i read on boostcruising that all skylines that rev towards the 5k range or reach the 10psi reigon suffer from flat spots. what they did was install a apexi safc, and it works perfectly now.

just throwing it out there. good luk

:):)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 🫠    
    • I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
    • But they do so for the other reasons to have a compressor bypass. It's in the name.
×
×
  • Create New...