Jump to content
SAU Community

Recommended Posts

Hello all,

see i've done my searching, and all i've read is that you have to either enclose the pod or put back the stock air box.

my question is however, when you get defected... do you get fined anything? like for example, a pod that is not enclosed gets defected.. will the owner have to pay anyone anything or simply just remove the pod?

and one more thing, what's better, a K&N panel filter or an Apexi lol, and if i get one of these for example, it will be inside my stock air box so if a cop checked under the bonnet they wouldn't notice anything right? and hence i wont get defected right?

sorry for what some may think are dumb questions, but i really need some answers lawl

Thanks

Link to comment
https://www.sau.com.au/forums/topic/180431-what-happens-when/
Share on other sites

Mate, i just finished clearing up my problem, I was done recently for a pod with a heat shield as my stock box wont fit over my intercooler piping, was told by the EPA officer he was going to take some shots then the head office will decide what to do as it was not "fully" enclosed.

Month later got the letter in the mail, $200 fine, and inspection needed by approved DECC officer, meaning it had to be done right,Source and refit old intercooler pipes, old box. but the wierd part is the mechanic told me over the phone i was going to have to do a noise test and emmissions test as these were affected by the air filter. My car was engineered for everything else so luckily didnt end up needing to do that( also as i passed the noise test at the pits thanks to EVC) but not sure what the exact process is they follow. Oh Inspection cost $40 at Archers in Granville, spoke to Craig a few times he was a top bloke helped me clear it.

Was told simply enclosing the pod 99% of the time will not pass if it is an EPA formal inspection as they dont pass or fail them, they only take photos and send them to EPA to decide, youre best off replacing the stocker and if you want to keep the pod in, get a custom fitted box for the pod made up like i am after you clear it.

The stock replacement panels for the standard air filter wont be a defect.

Edited by T187

HOLY SHIT! that means i could get fined up to $200!!!!!!!!!!!!!!!!! my gawd!

and you say "The stock replacement panels for the standard air filter wont be a defect." by that do you mean a high flow Apexi panel filter will be all good? plus do you noe which is better... K&N or Apexi.

Thanks!

Yea the panel will be fine, I mean if you want to talk legally any change affecting emissions needs to be engineered, but ive never heard of anybody being done for an upgraded panel filter so dont worry about it, the officer who looked at my car didnt even open up the box just had a quick look. the old "factory option/thats how i bought it" provides a bit of leniancy for those problems if it ever rises.

Sorry not sure which is better, ive got the Apexi panel and power intake pod if that helps ;)

Al

Edited by T187

haha it helps. but soz if im being a noob, but how can u have both? as in u own both? or have them both under the hood at the same time!?

thanks

p.s. by both i mean the power intake pod and the panel filter

Edited by CDA

well actually ive always used the pod as the box wont fit the larger piping, i have the box on now though thats also with the standard piping so thats less flow, and with the boost turned off, and with my HKS ecu unplugged, so i really cant compare them as you can tell theres a huge difference. I only ever tried playing with it a bit with my car all tuned and set once, and within 10 minutes one of the intercooler pipe hoses popped off from the pressure so never again...

But without an effecive heat shield and some sort of CAI theres no point in using a pod.

That would be painful if done by the epa. However when i got done for pod recently i had to get full inspection blue slip, pain in the arse if you have other things that the cops don't pick up on

did you have to pay a fine? coz if you did i reckon theres no point in a pod whatsoever

did you have to pay a fine? coz if you did i reckon theres no point in a pod whatsoever

No fine but the blue slip costs $50.30. Just enclose it, saves worrying about it. But they will always find something else if they want to be a pain

enclose it in a cone shaped enclosure or something more inconspicuous like the stock air box (is that possible?)

and ignuz sez: "I carry the paper around in the car now when cops get a little touchy about it" - that means you can flash that at a cop and they can't defect jack?

enclose it in a cone shaped enclosure or something more inconspicuous like the stock air box (is that possible?)

and ignuz sez: "I carry the paper around in the car now when cops get a little touchy about it" - that means you can flash that at a cop and they can't defect jack?

I'm sure you could somehow use the stock box, however there are numourous threads around about custom building boxes and there was a group buy a little while ago too. I have one that the old owner of my car had made from some metal just makes it looks all closed off.

Then to make it close to bullet proof get it engineered. Pricey but saves hassle later on

enclose it in a cone shaped enclosure or something more inconspicuous like the stock air box (is that possible?)

and ignuz sez: "I carry the paper around in the car now when cops get a little touchy about it" - that means you can flash that at a cop and they can't defect jack?

Oh they can if they want to raise some revenue or if I give them attitude.. But 99 times out of 100 they will look at it and say no worries..

I got done for mine by HWP last December

No fines, just had to pay for blueslip, who then demanded I have it engd, so it ended up costing me $350 (And that was a VERY discounted eng cert)

My engineer was in a happy mood, so yeah, cheap prices on eng cert.

A mate got done around 3 months ago in his R33 for a pod filter by HWP, and he copped a $70 fine.

It's up to who ever is issuing the defect notice whether they do or don't fine you, and how much it costs.

just a thought here

wouldn't the big 'ol metal clamped filters that are exposed to the engine bay that people fit on top on carby powered V8s be in the same boat 'flamability' wise as pod filters? hmmm...

Yea plus you cant rely on the cleared EPA notice, as my one clearly states it is not to be produced or shown to police when checking the car after it has been cleared...

simply, its gains vs costs, if you dont need it get rid of it,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
    • Continental have consistently beaten the absolute shit out of every other performance tyre in Wet/Damp/Cold conditions and give up a little bit of time (half a second at most) in the dry. Almost like it's engineered for German conditions or something. I'd def give those a try.
×
×
  • Create New...