Jump to content
SAU Community

Recommended Posts

For the R32 gtst (and maybe others?)...

Some numbers and other stuff to help with service parts:

Factory oil specs: 7.5w30 (but any rating as long as its synthetic / semi-synthetic is ok), 4.6L capacity

Oil filter: Z145A

Fuel filter: Z387

Spark plugs: PFR6A / PFR5A (NGK platinum) - gapped to 1.1mm or 0.8mm if you are missing

Tyres: 205/55/R16, 32psi - check the spare as well!

Water pump: 21010-21U25

Coolant: antifreeze-antiboil at 50:50 concentration, 9L capacity

Thermostat: 21200-42L05

Timing belt: 13028-20P10 - should cost around $80 mark

Hope this helps as lots of people post about this stuff all the time

I have collated the information as i see it and recorded it into a book for myself but decided to put it into the FAQ section to help everyone :)

Waz.

Link to comment
https://www.sau.com.au/forums/topic/18066-r32-maintenance-parts/
Share on other sites

  • 3 weeks later...
  • 4 weeks later...

ripped from www.rb20det.com

Water Pump: 21010-21U25

Thermostat: 21200-42L05

coil Packs: 22433 60u02 mcp-300124

Oil Filter Genuine Nissan: 15208-H8911

Oil Filter Ryco: Z145A

Oil Filter Valvoline: R9

Oil Capacity: 4.6L with filter (7.5w 30 is recommended)

Coolant Capacity: 9L

Manual Gearbox: 2L (80w 90)

P/s Fluid capacity, non-hicas: 1.8L

Sump washer 11026-01M02

Fuel filter 16400-53J10

Rear diff oil 1.5L

Alternator belt 11720-24U00

Cam belt 13028-20P10

PAS belt 11950-04U00

NGK standard plugs PFR5A-11 1.1mm gapped

NGK Iridium plugs T7341T-8 0.8mm gapped

Trust-Greddy Iridium plugs IT08 0.8mm gapped

Brake pads and discs for r32 gtst are the same as s13 200sx

Speedo drive gearbox end 32702-58S21

Air Flow Meter 22680-02U00

  • 1 month later...
  • 5 months later...
  • 1 month later...
  • 2 weeks later...
  • 1 year later...

ok,when my car was up on the hoist,i noticed like a drain plug at the bottom of the diff, is there one at the top aswell?

is there also a drain plug at the bottom of the gearbox?

automatic transmission

Edited by RSTME

yep one at the top, if u have a big exhuast then u might have to remove some section IIRC, i think the plugs take a half inch braker bar, maybe its 3/8

anyway, with auto trans it gets a bit more complex as your best removing the sump, and changing the filter inside etc, if your not comfortable with it, id reccommend getting somone to do it for you, sorry for the quick replys im dead, any questions feel free to pm

also, when draining things like diff always crack the fill before the drain, because if you undo the drain and the filler bung is stuck then you have a headache.

Edited by Jolinator

you'll find that the actual sensor is the same (titania, 3 wire, 12mm thread) - the only difference will be the connector type and cable length.

Another 'compatible' sensor is the OTD2F-B2 which originally suits an R31. If all you're after is the sensor, you can cut/splice/solder into the existing loom...

:D  I thought the part number for an NGK O2 sensor to suit a HCR32 was OTD2F-P1P ?!?!

  • 1 month later...
Z32 turbo and R32 turbo brake part numbers are the same.

DBA 909 & DBA 908. Same as the pads. Both the same part number.

My uncle bought a NA Imported Z32 which had slightly thinner disks.

Wrong, Only gts-t Type M has the 4 piston caliper like the z32.

Regular gts-t like mine, have the s13 200sx brake.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...