Jump to content
SAU Community

Recommended Posts

Looking to upgrade my car from a GTT to a v35 and also at the same time buy an r34 GT for my brother

Before I do that I need to get rid of my current car which I will be putting it up for sale/trade.

Just wanted to ask if anyone has or know anybody who has sold/traded their cars at an import car yard?

There are plenty of these on Parramatta road but do they all buy/do trade in?? I understand that they’ll usually try to rob you blind but just wanted to hear from someone’s experiences

Looking at the private car market, selling a car is too time consuming (organising to meet, time wasters, risk of getting jacked) and in the end, it seems like many sellers have to drop the price considerably anyways.

Cheers

Eric

Link to comment
https://www.sau.com.au/forums/topic/181766-sellingtrade-ins-experiences/
Share on other sites

Unfort at this time mate, the market for Skylines has dropped a fair wack so private sale will take a while to sell, and theres so many out there that the sale price you ask, 90% you'll never get.

If you need a quick sale to buy the new car, perhaps trade in might be the easiest, quickest way?

I traded my R33 GTS-T in. It was maybe $1000 or $2000 less than the market value (maybe not actually seeing that it was suffering from some electrical and ABS issues) but yes you'll find its way more convenient than the whole private selling thing.

Remember when negotiating trade value to say to the dealer that you will not be including the mods.

You'll be able to sell the mods separately for more money and the dealer probably won't care but its just to cover your ass just in case upon trade-in he's wondering where that FMIC went.

trade in value will be an absolute lowball offer.

e.g. I have a ford falcon AU sII 70 000ks which my parents are trading in atm. I can't be bothered to sell it for them and they're lazy.

Toyota offered 4k max, which is a downright shit offer if you ask me. Quite a bit lower than market value. e.g. look at what you can get for 4k on carsales - an old vl/vn fangadore or el/ef falcon

hi eric

how u and ronz doing...havent seen u guys for a while

im looking to get an s15 atm and i went to japlink imports on parra rd and i showed them all the specs of my car...like yr, model,km's mods even with full thread on tyres and full yr rego etc... and they go it's worth 10k (even with everything done to my car)... as i was expecting it to be alot more

personal opinion...i have never been back there

Nick

Edited by skyline17

to get a good idea of what the trade in price might be try going to www.redbook.com.au that way you can be prepared and not take the crappy offers that you will know are way under market/trade in value this is the site that most dealers use.

well it works like this. some places will give you a great trade in value, then reamn you on the price of the car you are buying. other places will give you a nasty trade in price, but may play ball with the car they are selling you. either way you still get screwed and for the dealer their change over remains the same. it's just a different way of spinning it.

sell the car, then buy the car you want. much better option.

well it works like this. some places will give you a great trade in value, then reamn you on the price of the car you are buying. other places will give you a nasty trade in price, but may play ball with the car they are selling you. either way you still get screwed and for the dealer their change over remains the same. it's just a different way of spinning it.

sell the car, then buy the car you want. much better option.

The thing to focus on with the dealer is the changeover price (on road). How it is broken up is completely irrelevent.

Some yards will give you a good trade & pineapple you for the price of the new car.

Some will give you a lousy trade & a cheap new car.

All you should care about is the changeover price.

Best option is to sell your car privately & then front the dealer with cash. The expression "look mate I have the money now & will buy it now if you can do a better deal" will always garner their interest. Particularly if it is nearing the end of a bad month/quarter.

Ofcourse, you could always buy privately, too.

Good topic, I actually work in the car industry in sales atm with Subaru Australia.

Trade in values will always be lower, as they will always need to make something off your car, otherwise why would they buy it? If you private sale your vehicle, you will get alot more than a trade in price. That way you have the most money you can get, then go negotiate on the car your looking at. Used cars tend to have very good margins in them from experience.

Just remember theres 2 factors to the equation.

1) The actual car itself. Now this could have something like $8k in the car, and thus is quite abit of movement to use.

2) The trade in. You may get a good offer on the trade, ie market value is 15k and they give you 14k, however in terms of a real figure on the trade of what they would trade your car for would be like 10k, thus overallowing 4k on your trade, meaning they take a 4k discount on the car, but still profit $4k at the end after the whole thing, plus whatever they sell your car for, ie if they sold your trade for 17k, thats $7k profit all up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...