Jump to content
SAU Community

Recommended Posts

hey guys

looking at purchasing a 33 series 2,

however the guys says he only services every 10,000k, because he uses semi-synthetic oils

everyone else claims to service theirs every 5,000k, using what i assume are synthetic oils

whats the go? is it alright to only service every 10,000k?

thanks

Edited by anomaly
Link to comment
https://www.sau.com.au/forums/topic/182307-semi-synthetic-oil-servicing/
Share on other sites

i think its a personal choice really, i get my r34 gt done every 5,000km's but the engine is quite tired and i wanna try and reduce nething to go wrong by getting it checked regulary(and due to the fact i can do up to 500kms a week sometimes)

hey semi synthetic oils or fully synthetic oils last no longer than a conventional mineral based oil they just offer superior protection but still need replacing at regular intervals. most owners of performance cars change every 5K but that is just to offer their car the best protection they can. it is up to you wether you choose to change every 5 or 10. i know some new cars are going 15 between manafacturing servicing i just can't work out why anyone would even let it go that many with no change.

I guess it is Ok to go 10,000 but just keep in mind, turbos give oil a hard time, and if the car is driven in anger (don't kid yourself, it's a performance car for exactly that), the oil is given a hard time more often, so you want the oil changed before it starts to degrade.

Servicing every 5,000 ensures this doen't happen. So while 10,000 is not excessive and may be OK, 5,000 is better.

If you're servicing every 5000kms and the oil looks the same when it comes out as when it went in, then you're probably over-servicing.

Most late model cars now only require servicing every 10,000kms.

Personally I use fully synthetic oils and I wont be changing the oil any more often than every 10,000kms. My car is a 99 model with low kms though so with a 10-15 yo car it might pay to service it a little more often. Its your call.

A lot of people are just paranoid that if they drive a km over 5000 km their engine is gonna blow up.

Servicing every 5000km is going to make buying synthetic oil very expensive. Personally I'd rather change the oil every 10,000kms with fully synthetic oil than every 5000 with mineral oil. Just my opinion...

i have had my non turbo r33 for 7 months and done around 15,000k's i didnt get it serviced when i first got it. i really think i should get it serviced =/ the last thing i want to do is hurt my baby

its one of those things i keep putting off *slaps himself across the head*, what should be changed at the 100,000k service?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...