Jump to content
SAU Community

Recommended Posts

Okay,

Went in expecting around 180ish rwhp, as my car was misfiring on 7psi..... *sigh*

Pulled 208.8hp@7psi (not bad for stock boost) with a power curve that looks like a set of stairs....

I gots Zorst (w/front pipe), POD, Cold Air, and stock boost...

after having a chat to steve he commented that the timing was retarded a bit, and suggested i advance it a bit for more power... what a difference that made! was able to up the boost to 11psi, no misfiring at all, and the power pulled all the way to redline... DAM.. Kym wants another run!!!!!!

Thanks for the advice steve, i'll be back to tune the new AFC and EBC real soon...

-Kym

edit - Mod :don't forget the no cat kymbo which gives about 10-15 at the rears from the cars i've seen with it and without it.

Link to comment
https://www.sau.com.au/forums/topic/18310-sst-dyno-day-post-your-results-mods/
Share on other sites

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

I hate to steal their thunder.....but :D

There were 2 manual NA RB30's R31's both around 135rwHP

And a very sweet lookin Manual RB20DET GTS-X which put down 137rwHP

I think my wagon was a off the pace due to being auto...manuals were held in 4th, my auto was in 2nd I believe. :O

Originally posted by adam 32

strich9: so your car was misifiring cos the timing was retarded?  

what revs was it misfiring at? (i only ask cos ive got a bit of a flat spot at the moment im trying to sort out)

Yep, Sure was Adam. As soon as I cas-bashed it a bit 2mm (on the cas) advance, all the misfiring stopped except for a small pop ord two between 4-5rpm. Immediately the car pulled like a train and I was able to wind the boost all the way up to 11psi. I HAD to run 7psi before or the misfire was really bad...

It also had MAJOR flat spotting before the timing was corrected.

Attached my dyno sheet :D

dynosst.jpg

343.6 at 1.2 bar on std ceremic terbs with boost control going all over the place. No damage done and boost control now sorted (I wound up the boost and left the duty cycle at a default 60% which is way too high compared to what has been "self learnt" for the lower 1.0 bar boost).

Mods: HKS engine pipe, Jap spec cat, HKS Hiper Zaust, PFC with boost kit. Normal boost 1.0 bar delivered 318 hp atw previously.

Mine managed to get itself to 210.2 HP. Got to 198 with nothing tuned then Steve quickly added fuel to my top end which got me to the 210. Will have to get my S-AFCII tuned properly and wind a bit more boost into her. Might help if i make a partion for my HKS pod, damn that thing's noisy.

For mods, see signature. Note: Nothing tuned yet....

Originally posted by S13_Angel

233.7hp @ 12psi

fmic, pod, 3" zorst (turbo back), badbiki.

very impressive angel, no wonder shes such a sleeper

as for me see the sig its got all the info, theres more roomto play but i don't think it would reliable then

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...