Jump to content
SAU Community

Recommended Posts

Any one know of some one wrecking an M35 in SA, I'm chasing a couple of interior parts...

Mike.

I saw a V35 down at the dry creek wreckers on lower churchill rd. They might have a few interior parts the same. I have a few dash parts.

Can someone here please confirm that 19" wheels by 8" offset +38will fit our m35s?

As far I as checked "yes" but it 's always good to double check...

also any issues at lowering the car with those wheels?

Cheers

Can someone here please confirm that 19" wheels by 8" offset +38will fit our m35s?

As far I as checked "yes" but it 's always good to double check...

also any issues at lowering the car with those wheels?

Cheers

19x8" +38 offest will fit fine; but they'll look crap, miles too far inside the guards. Needs at least +30 offset with 8"width.

19x8" +38 offest will fit fine; but they'll look crap, miles too far inside the guards. Needs at least +30 offset with 8"width.

mine are 8.5 +20's and they sit flush i needed to roll the rear guards abit though.. but only coz im abit to low, and ARX sized tires.

So, i finally got my car down to a Nissan dealership and plugged into a Console II. (for those just joining us i have had an issue with the 4WD light staying on) The code that was spat out was C1206 which is the 4WD motor. So the issue is either with the motor its self, which is attached to the transfer case, or the wiring some where, which is a possibility as there was some other alterations to the cabling.

Mike.

the motor for the attesa system is under the boot floor on the driver's side.

Any idea what it looks like?

Is it inside the car or underneath?

I have all of the drives side side trim out to gain access to the Altessa computer so is it near by?

Mike.

No, no, the pump is under the rear (boot) section of the car... behind the rear wheel.

You can see it clearly from under the driver's side of the rear bumper.

Sorry there may be some confusion... The problem is to do with the 4WD Motor not the pump, well this is what the Console said. Are they one and the same or different parts?

Sorry there may be some confusion... The problem is to do with the 4WD Motor not the pump, well this is what the Console said. Are they one and the same or different parts?

same thing....there is only a 4WD ECU, transfer case, oil can and pump motor.

unless they mean the ACTUAL tranfer case at the back of the gearbox?

Well if the transfer case is entirely mechanical and clutches then it must be one of the motors under the rear of the car, would you recommend just taking it to an auto electrician to get them to see if the motor is faulty? is it something they will be able to tell?

youre right, the transfer case is only clutches and a chain drive.

the pump is where we have already mentioned. if the pump is gone, its not a cheap exercise. however it might be something easy like the attesa ECU or a relay etc.

you can hear the pump start when you start the engine. if you dont, then its something related to that.

have you checked the fluid level in the boot??

youre right, the transfer case is only clutches and a chain drive.

the pump is where we have already mentioned. if the pump is gone, its not a cheap exercise. however it might be something easy like the attesa ECU or a relay etc.

you can hear the pump start when you start the engine. if you dont, then its something related to that.

have you checked the fluid level in the boot??

Ok I'm in the same boat.

Fluids are full.

Pump starts when I start the car, but it makes a chirping noise every 5 sec then eventual it gives up. Then I get the 4WD warning light.

thats the pump turning on and off. it will do that till it gets pressure then i believe it only turns on to maintain pressure - i could be wrong.

ok sounds like you have another problem. mine also does that, but not all the time. it may depend if im parked on a slope etc also

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...